The steel pipe in (Eigure 1) has an inner diameter of 3.54 in, and an outer diameter of 3.79 in. Figure 12 in 12 in. 1 of 1 60 lb If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. VE] ΑΣΦ | it voc 1, Submit Provide Feedback Request Answer ? psi, psi Next

The steel pipe in (Eigure 1) has an inner diameter of 3.54 in, and an outer diameter of 3.79 in. Figure 12 in 12 in. 1 of 1 60 lb If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. VE] ΑΣΦ | it voc 1, Submit Provide Feedback Request Answer ? psi, psi Next

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The closed thin-walled tank has an inner radius of r and wall thickness t and contains a gas of pressure of p. The state of stress at point "a" on the surface of the tank is represented by stress components with an unknown stress element rotation angle of 0. Note that, the two normal stress components for x'y' system (note: not xy system!) are known: ox, = 120 MPa and Oy = 180 MPa, but the shear stress component (T,) is unknown. Determine: (1) the principal stresses at point a ; (2) Tx'yı ; (3) rotation angle of 0 . y 180 MPa 120 MPа х 0 = ? a Tyy = ? tank cross section stress state at point a
Solve correctly please.
a. Determine the principal stresses at point A on the cross section of the wrench at section a-a. Also Specify the orientation for this state of stress. b. Determine maximum in-plane shear stress at point A on the cross section of the wrench at section a-a. Also Specify the orientation for this state of stress.
Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 Ib 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please I =
3. A circular steel cylinder of external diameter 0.2 m and internal diameter 0.1 m is shrunk onto a circular aluminium alloy cylinder of external diameter 0.1 m and internal diameter 0.05 m, where the dimensions are nominal. Determine the radial and hoop stresses at the bores and outside surfaces, such that when there is an internal pressure (retained by end caps) of 300 MPa, the maximum hoop stress in the inner cylinder is 150 MPa.
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 5 MPa in size. (a) Determine the stresses O, Oy, and the magnitude of Tyand show them on a stress element. (b) Determine the stresses o, o, and the magnitude of Tnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between thexand n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise). Answer: (a) o i MPa Oy. i MPa MPa (b) On-1 MPa MPa MPa Save for Later Attempts:0 of 1 used Submit Answer
A cylinder of (320) mm inside diameter and (64) mm thickness is subjected to an internal pressure of 15 MPa. Find the variation of circumferential and radial stresses in the shell and plot them. What is the increase in the inside and outside diameters of the shell? Take E=200 GPa and v=0.3
Can you please solve this homework problem with step by step solution
None
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
Determine the principal stresses at points A and B of the cylinder. Consider: L = 70 mm; d = 20 mm; F = 12 kN; P = 15 kN; T = 800 Nm.
Mohr’s circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 16 MPa in size. (a) Determine the stresses σx, σy, and the magnitude of τxy and show them on a stress element. (b) Determine the stresses σn, σt, and the magnitude of τnt and show them on a stress element that is properly rotated with respect to the x-y element. The sketch must include the magnitude of the angle between the x and n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise).