Normal stresses expression:Shear stresses expression:OB (i. e., ox) =Tg-y (i.e., Txy) =Tg-z(i. e., TxE) = Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses atpoint B on the shown cross-section. (b) Show the state of stress at the point B on a volumeelement.400 lbB1 in.2 in.500 Ib2 in 10 in.1.5 in.1.5 in.Show your steps and highlight the following answers pleaseI =

convert lb to kN 500 lb = 2.24 kN 400 lb = 1.78 kN convert inc to mm 1 in = 25.4 mm 10 in = 254 mm…

[I'wo forces are applied on the beam shown below. (a) Determine the normal and shear stresses point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 1b 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please A = Q =

[I'wo forces are applied on the beam shown below. (a) Determine the normal and shear stresses point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 1b 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please A = Q =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In each case, the state of stress sx, sy, txy produces normal and shear stress components along section AB of the element that have values of sx = -5 kPa and txy = 8 kPa when calculated using the stress transformation equations.Establish the x and y axes for each segment and specify the angle u, then show these results acting on each segment.
#3 handwritten then box the final answers
- once answered Correctly will UPVOTE!!
Determine the maximum value of the force P (kN) that can be applied to member AD if the allowable stress is 200 MPa and the maximum upward displacement of point A is 3 mm. Use E=100 GPa The values of the cross-sectional area, and L1, L2, and L3 are given in table below for each student. P A L1 12 kN L2 9 kN L3 LI (m) (m) Student Cross-sectional area L2 L3 ID (mm?) (m) 1.45 1131731 200 3.8 1.2
Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 4.3 kN given t=5 mm, a=5.5 mm, b=5 mm, F0.5 mm, and D=2.2 mm. [note: Drawing is not to scale] P O 275.20 MPa O 734.26 MPa O 172.00 MPa O 1915.45 MPa O 716.67 MPa O638.48 MPa O573.33 MPa O 677.58 MPa
3.
A member is subjected to a major stress of 110 MPa (tensile), minor stress of 40 MPa (tensile) along with a counter clockwise shear stress of 30 MPa. Calculate the Normal stress, tangential stress, Resultant stress and its inclination on plane make 20 to major stress. Validate your analytical results by drawing Mohr’s circle. i) Normal Stress (unit is MPa) = (ii) Tangential Stress (unit is MPa) = ) Resultant Stress (unit is MPa) Resultant inclination (unit in degree) =
Consider the loading shown. The allowable normal stress for the steel used is 172 MPa. For the selected design, determine the maximum value of the principal stress σmax at the junction of a flange and the web. (Round the final answer to one decimal place.)
The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam at point A located on the web at the bottom of the upper flange. Although it is not very accurate, use the shear formula to calculate the shear stress. A B₂ ➜ 10 mm- B 200 mm 12 mm 250 mm 12 mm -3 m 50 kN
The assembly supports a uniform distributed load = 1.65 kN/m as shown. Part A Determine the resultant internal loadings at cross sections at point on the assembly. Express your answers, separated by commas, to four significant figures. V AZO NE=, VE =, ME = Submit Request Answer Part B Determine the resultant internal loadings at cross sections at point F on the assembly. Express your answers, separated by commas, to four significant figures. Np. Vp, Mp= Submit Provide Feedback VO ALO 63 12 Request Answer 1? kN, KN, KN-m kN, KN, KN-m D E 0.5 m 0.5 m 0.5 m B Im -1.5 m 2 m
Determine the principal stresses in the beam at point A. Specify the orientation of the element representing the principal stresses. 150 kN 60 kN 50 mm A A [150 150 mm 60 mm 0.5 m -0.25 m-
The state of in-plane stress at a point on an element of material is shown. Let |σx| = 370 MPa, |σy| = 130 MPa, and |τxy| = 85.0 MPa. Use this information to represent the state of stress of the same point that is rotated through an angle of θ = 25.0.