-0.8 ft- 20 lb 1.50 ft 0.5 in. 80 lb [3 in. 0.5 in." 5 in. "0.5 in.

Q: The solid axle has a diameter of 40 mm. It is subjected to a shear force of 1 1. kN along Z-axis and…

A:

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

A:

Q: 5 kN.m is applied to the purlin in a plane at an angle of 30 deg to the vertical y axis. If the…

A: givenM=5000Nm, θ=30οMx=5000×103 cos30ο=4.4×105 N-mmMy=5000×103sin 30ο=2.2×105 N-mm

Q: The aluminum machine part is subjected to a moment of M = 75 N.m. (i) Determine the bending stress…

A:

Q: The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b =…

A: Given Data B=250 mm D=400 mm d=20 mm(steel bar) P=400 kN

Q: Below Figure shows the section of an angle purlin. A bending moment of 5 kN.m is applied to the…

A:

Q: of 3.0 mm is produced at the tom of the groove. Compute the maximum stress in the rod y axial…

A:

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm.…

A: Inside diameter = 300 mm Inside radius = 150 mm outside radius = 260 mm internal pressure = 80 Mpa

Q: Determine the moment M that must be applied to the beam in order to create a maximum stress of 90…

A: Given Data Maximum stress to be created is : σ=90 MPa Now draw the cross-section of the beam

Q: Determine the maximum tensile (fot) and compressive (foc) stresses (psi) developed in the…

A: Objective: To determine the maximum tensile stress fbt and compressive stress fbc.

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

A:

Q: Determine moment that will produce a maximum stress of 60 MPa on the cross section. To 3 significant…

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-16 aluminum. If a couple forces P =…

A: As applied force is at some distance from the longitudinal axis. so it generates torque and the…

Q: The cylindrical steel column has an outer diameter of 90 mm and inner diameter of 80 mm. T column is…

A:

Q: KIN 14 kN / m 10 kN / m A B ID 4 m 2.5 m 2.5 m 3 m

A: Finding support reactions:RA+RB=12*4*14+14*5+20+30RA+RB=148…

Q: Q1: Find the maximum flexural stress in the shown beam. 30 kN 50 kN to 100 mm 1m 3 m 2 m 80 mm

A: A pin support will exert both horizontal and vertical components of the reaction. The support B is…

Q: Write the mathematical expression for the internal shear in segment CD in terms of x with point A as…

A: For the solution refer below images.

Q: circular tube AB is fixed at one end andfree at the other end. The tube is subjected to axialforce…

A:

Q: The beam is supported by a Pin at A and a short link BC. If P = 15 kN, determine the average shear…

A:

Q: Given the section is subjected to a moment of 500 N-m, calculate the normal stress in MPa at the…

A:

Q: Determine the maximum positive normal bending stress that occurs in member ABC of the engine crane…

A:

Q: 2. If the bending stress at section 2 =20 MPa. What are the bending stresses at sections 1, 3, and…

A: Given data:        From equation of pure bending                                MI=σby=ER…

Q: Determine the absolute maximum bending stress in the 80-mm-diameter shaft which is subjected to the…

A: Diameter of the shaft, d= 80 mm Note: Let the 12 kN force is acting at point "C" and 20 kN force is…

Q: For the surface area shown below, determine the second moment of area, the location of the neutral…

A:

Q: The rigid bar AB and CD are supported by pins at A and D. the vertical rods are made of aluminum and…

A: Given Data For bar AB L=4 ft A=0.75 in2 E=10×106 psi   For bar CD L=5 ft A=0.25 in2 E=12×106…

Q: If M=2.5kip.ft, determine the magnitute of the resultant force the bending stresses produce on the…

A:

Q: A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm.…

A: Given: The beam with a rectangular section 85mm x 302mm or 0.085m x 0.302m. The beam is subjected to…

Q: 4. The beam is subjected to the internal moment M = 1200 kN-m. Determine the bending stresses at A,…

A: Given:M = 1200 kN-m

Q: M 300 N m 16mm mm C. 40 mm-- 40 mm

A:

Q: The simply supported joist is used in the construction of a floor for a building. In order to keep…

A: Understand due to symmetry of the beam the reactions offered by the supports will be equal and…

Q: M E. х Solution: The moment of inertia of the cross-section about z and y axes are 1 Iz AB³ |(10-)…

A:

Q: A 3.2 m B- 1.5 m 180 mm 30 mm 125 mm 200 mm 30 mm

A: (a) To find: The maximum concentrated force. Given: The allowable tensile strength is σt=4 MPa106…

Q: 1. 100 mm The bar has a diameter of 60 mm. If it is subjected to the force components as shown in…

A:

Q: he axle of the freight train is subjected to loadings as shown below. The diameter of the axle is…

A: Given:The diameter of axle is .Free body diagram.Here,  is reaction force at C and is reaction at…

Q: Determine the internal normal force, shear force, and moment at points A and B in the column.

A:

Q: 6-126 The wooden section of the beam is reinforced with two stedl plate as shown. II the beam is…

A:

Q: The simply supported joist is used in the construction of a floor for a building. In order to keep…

A: The given load is 600 lb =P The reaction at the supports is 600/2=300 lb The allowable shear stress…

Q: 4–3. The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the…

A: The free-body diagram of the bar AB is represented as below. At equilibrium, ∑Fx = 0 FAB - 9kN = 0…

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P =…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.