Below Figure shows the section of an angle purlin. A bending moment of 5 kN.m is applied to the purlin in a plane at an angle of 30 deg to the vertical y axis. If the sense of the bending moment is such that both its components Mx and My produce tension in the positive xy quadrant, calculate the maximum direct stress in the purlin, stating clearly the point

Below Figure shows the section of an angle purlin. A bending moment of 5 kN.m is applied to the purlin in a plane at an angle of 30 deg to the vertical y axis. If the sense of the bending moment is such that both its components Mx and My produce tension in the positive xy quadrant, calculate the maximum direct stress in the purlin, stating clearly the point

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

use kN-m as unit for the final answer
2. The figure shows a cantilevered beam, subjected to a uniformly distributed (rectangular) 40 N/m force along the section DE, a 50 N point force at point C, and a 200 N·m couple moment. a. Write the shear-force and bending-moment equations as a function of distance, x, measured from the leftmost point, A, for the entire beam. b. Using your shear-force and bending-moment equations, calculate the shear force and bending moment at x = 2 m and x = = 5 m. 200 N·m 50 N 40 N/m 1.m C D 2.5 m 1m 2.5 m E B 2 m
The internal loadings at a cross section through the 120-mm-diameter drive shaft of a turbine consist of an axial force of 12.5 kN, a bending moment of 1.2 kN - m, and a torsional moment of 2.25 kN m. (Eigure 1). Figure 1.2 kN-m 12.5 kN 1 of 1 2.25 kN-m
In the figure shown, the aluminum strut has a cross-sectional area in the form of a cross. If it is subjected to the moment M= 8 kN.m: 1) determine the bending stress acting at points A and B, 2) show the results acting on a stress distribution diagram.
Compute the following.
For the beam shown at right, determine the following: P= 1800 lb a. Maximum tensile bending stress b. Transverse shear stress at a the junction of the "TEE" (i.e., 2" above the neutral axis). c. Transverse shear stress at the neutral axis - 7.5 ft- - 7.5 ft- (a) d. Draw the stress elements -10 in. representing the state of stress at the junction of the “TEE" and at the neutral axis. | 2 in. 4 in. -N- 1600 10 in. 8 in. 42 in.k- (b)
Solve for the moment about A, B,C , as shown in Figure .Take the force F = 1320 kN and P=660k?
strength of materials
Draw a FBD of section CD. Do not solve the rest of the problem
A solid rod has a diameter of e = 55 mm and is subjected to the loading shown. Let a = 200 mm , b = 210 mm , c = 310 mm , d = 250 mm , and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) a. As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x-axis, Mx. b. To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm, find the stress σA due to the normal force. c. To find the state of stress at A, the principle of superposition must be used. If the rod has a diameter of 55 mm, find the stress σA due to the bending moment about the x-axis. d. To find the state of stress at A, the principle of superposition must be used. Find the stress σA due to all of the loadings on the rod.
If the I-flange beam is subjected to a shear force V = 20 kN, calculate the transverse shear stress at the point A (considered located on the web part). The area moment of inertia of that section about its neutral axis N.A. is INA = 44.167 x (106) m4. Flange Web Select one: O 41 MPa 10 Mpa O 4.95 MPa O O 50 MPa 100 MPa 20 mm 100 mm A 100 mm 25 mm 150 mm 25 mm
Solve q2