The aluminum machine part is subjected to a moment of M = 75 N.m. (i) Determine the bending stress created at points B and C on the cross section; (ii) Determine the maximum tensile and compressive bending stresses in the part.

Q: A 4- cylinder diesel engine running at 1200rpm developed 18.6KW. The average torque when one…

A: The performance of any engine is described by its efficiency. There are mainly five types of…

Q: A wooden beam is fabricated by nailing together three boards as shown. The boards have dimensions…

A:

Q: A solid rectangular homogeneous section (total length = 7.2m) is simply supported, where b = 50 mm…

A: Draw the schematic diagram of the beam representing the forces.

Q: If the allowable stress due to bending in the beam shown below is Omax = 150 MPa, is the beam able…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine the bending stress (in psi) of wire rope with drum diameter of 10 inches and wire diameter…

A: Given data Radius of curvature (R)=10 in Wire diameter (d)=0.1 in Wire radius(r)=0.05in Young…

Q: 7. Straight rods of 0.4ft diameter and 100ft length are stored by coiling the rods inside a drum of…

A:

Q: The steel beam with given support condition and section is being loaded as shown. (a) Draw shear…

A:

Q: For the given section, (a) determine the moment of inertia about z & y-axes. (b) if the section is…

A:

Q: For the overhang beam with the cross-section and the applied loads shown, (a) sketch the FBD of the…

A: Givenoverhanging beam  as shown below

Q: .6-49. Determine the maximum tensile and compressive bending stress in the beam if it is subjected…

A: To Find : The maximum tensile and compresive bending stress Given : The moment is The free body…

Q: The lever must exert a force of P = 3800 Ibs at B as shown. The lever lengths are a = 11 in. and b =…

A: To find : determine the minimum thickness t that can be used for the lever . Given : force P=3000lbs…

Q: For the 80-mm shaft subjected to two concentrated forces shown, the journal bearings forces. Address…

A:

Q: Smooth journal bearings at A and B that only exert vertical reactions on the shaft as shown below…

A: The diameter is .

Q: 3.35B. For the section illustrated, find the second moment of area, the location of the neutral…

A:

Q: For the stepped bar, determine the maximum bending stress (in MPa). Express your response using…

A:

Q: Example 2 The symmetric notched plate is subjected to bending. If the radius of each notch is r= 10…

A: Introduction: Primary bending stresses are caused by prolonged loads and have the potential to cause…

Q: Determine the maximum positive normal bending stress that occurs in member ABC of the engine crane…

A:

Q: Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum…

A: Given

Q: The rectangular beam shown is made of a plastic for which the value of the modulus of elasticity in…

A:

Q: Determine the absolute maximum bending stress in the 80-mm-diameter shaft which is subjected to the…

A: Diameter of the shaft, d= 80 mm Note: Let the 12 kN force is acting at point "C" and 20 kN force is…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.