For the given section, (a) determine the moment of inertia about z & y-axes. (b) if the section is subjected to Mz= 10 kN-m and My-25 kN-m, determine the maximum tensile bending stress and find its location on the section (use the notation of A, B,C, and D). 15 mm 50 mm 2 + 50 mm C 15 mm 10 mm 100 mm 8

Q: 300 N ·m 1 m 1000 N · m D 1.5 m 1 m

A:

Q: An orthopedic implant is being designed by a biomedical engineer. The implant needs to be evaluated…

A:

Q: 2-11. Determine the plastic distorts as shown by the dashed lines. 3 mm y C 300 mm the shear strain…

A:

Q: 1-5. Determine the resultant internal loadings acting the cross section at point B. 60 lb/ft

A:

Q: *3-6. The springs AB and BC have a stiffness of 500 N/m and an unstretched length of 6 m. Determine…

A: Given:To find:Displacement 'd' of the cord from the wall.

Q: The square deforms into the position shown by the dashed lines in. The dimensions are S=49 mm, S′=54…

A: Given data- S=49 mm, S′=54 mm, Δx1=5 mm, and Δx2=9 mmDetermine-A) the shear strain at A relative to…

Q: 7. Straight rods of 0.4ft diameter and 100ft length are stored by coiling the rods inside a drum of…

A:

Q: Find Δ v at point A, consider flexural deformation only. El is constant. Hint: locate the origin of…

A: Calculate the reaction at C: ∑Fy=0Cy=2×3+12×18×3Cy=33 kn,Cx=0Mc=2×3×1.5+12×18×3×33Mc=36 kN·m Moments…

Q: Question 1: A member having the dimensions shown is used to resist an internal bending moment of M…

A: ◆ The moment of inertia of the cross-section: Iz = 63.6162 × (10-6) , m4 Iy = 0.1112787 × (10-3) ,…

Q: The beam supports a distributed load with a maximum value of 80 lb/ft at A. Part A Determine the…

A: Given data  Distributed load = 80 (lb/ft) Find the internal loading at B

Q: Question 2: The load binder is used to support a load. An external moment, MA is applied to the…

A:

Q: The beam supports the triangular distributed load shown below with Wmax = 510 lb/ft. The reactions…

A: According to the question data triangular loading beam is given we need to determine the internal…

Q: Determine the absolute maximum bending stress in the 80-mm-diameter shaft which is subjected to the…

A: Diameter of the shaft, d= 80 mm Note: Let the 12 kN force is acting at point "C" and 20 kN force is…

Q: Determine the axial displacement of point C with respect to the fixed end support B if the rod is…

A:

Q: Determine the resultant internal loadings acting at the circular cross- section passing by points A…

A:

Q: Determine the resultant internal loadings acting on the cross sections at point F of the frame.

A: Given DataThe tensile force P=185lbFind outa) The resultant internal loadings acting on the cross…

Q: *4-132. Replace the loading acting on the beam by a single resultant force. Specify where the force…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.