2-11. Determine the plastic distorts as shown by the dashed lines. 3 mm y C 300 mm the shear strain Yxy at corners D and C if 4 mm D -400 mm- 12 mm B A 5 mm 8 mm 12 mm X 2

Q: At what angle theta will both boxes begin to slide.

A: m1=65lbs = m2

Q: Among all the statements below about a 2D stress element, choose all which are true. Normal stress…

A:

Q: Find Ax and Ay F2= 450 N 45° 14- y F₁ = 300 N Ay 5 3 Ax F3 = 600 N -X

A:

Q: In Figure Q2, a = 58 mm and the origin of the coordinate system is at centroid of the cros section.…

A:

Q: Determine the average normal strain along diagonal DB, based on the original plate (blue) and the…

A:

Q: Replace the loading by an equivalent resultant force and couple moment acting at point O (Figure 1).…

A:

Q: The rod has a diameter of 40 mm. It is subjected to the force system Fx=1100 N, Fy=500 N, Fz=900 N.…

A: The forces are The diameter od rod is The torque is

Q: Required information Consider the given state of plane strain. Ex=-180µ, Ey=-260µ, Yxy=+295µ Use…

A: By the Mohr's Circle as shown below

Q: Q/ If P1= 450N and P2 = 650 N, Calculate EF, and EF, using x'and y'axises y P1 P21 30°

A: Given data: P1 = 450 N P2 = 650 N Need to determine the value of equivalent force along x and…

Q: 1. Find the relationships between strain components in the polar coordinate and strain components in…

A: To find the relationships between strain components in the polar coordinate and strain components in…

Q: The square deforms into the position shown by the dashed lines in. The dimensions are S=49 mm, S′=54…

A: Given data- S=49 mm, S′=54 mm, Δx1=5 mm, and Δx2=9 mmDetermine-A) the shear strain at A relative to…

Q: (NOT IN SCALE) Determine the direction of angles of a force vector F, where 01 = 40°, 02 = 20°, and…

A: Write the force F in vector notation by projecting it components on the x, y and z axes…

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 125 KN,…

A:

Q: - The square plate is deformed into the shape shown by ormal strain along diagonal AC and the shear…

A: Calculation for normal strain in AC

Q: Required information Consider the given state of plane strain. Ex =-180µ, Ey=-260µ, Yxy= +295µ Use…

A: Since you have asked multiple questions, only the first question is solved for you. If you want any…

Q: 4-2* Delecmine ihe moments of the 225-N foce shown in Fig. P1-2 about piints A, E, and C. 200 me+200…

A: According to given Condition  The moment at A can be given as MA=225(400+200)MA=225×600MA=135000…

Q: 2. The two wires are connected at A. If the force P causes point A to be displaced horizontally 2…

A:

Q: The piece of steel shown was initially rectangular in shape. Determine the average shear strain…

A:

Q: Variable F₁ d₁ d₂2 Values for the figure are given in the following table. Note the figure may not…

A: The beam is supported by rods AB and CD that have different cross-sectional areas. The area of rod…

Q: The strain components ɛ, Ey, and yy are given for a point in a body subjected to plane strain. Using…

A:

Q: *2-96. The tower is held in place by three cables. If the force of each cable acting on the tower is…

A: Givenx=20my=15m

Q: The ratio of decrease in length to the original length is known as compressive strain. Select one:…

A: