4 The state of stress on an element at a point is described by the Figure shown. Stress magnitudes: 0x = 120 MPa, oy = 200 MPa, Txy = 80 MPa (a) Neatly sketch the Mohr's Circle, identifying the locations of the two principal stresses and the two maximum in-plane shear stresses. (b) Determine the magnitudes of the stresses using the circle. (c) Determine the orientation of the stresses using the circle. (d) Sketch the results Txy

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: For the problem shown below, you are given x1 = 0.28 m, x2 = 0.05 m, x3 = 0.18 m, and y1 = 0.07 and…

A:

Q: The tension is 850 lb in cable AB and 950 lb in cable AC. y B 45 in. Wood Floor 40 in. C 60 in. 65…

A:

Q: 500 lb 1 300 16 722 16 FIND : RESULTANT OF ALL FORCES MISSING 4TH FORCE FOR RESULTANT TO BE 500 16…

A: GivenResultant force =R=500 lb↑

Q: QUESTION 3 -50" B 50" A ♫ 11" 13" The bucket and its load have a combined weight of 4000 lb with…

A:

Q: Can you please draw Mohr's circle for the solution above?

A: Given that, σx=350 MPaσy=230 MPaτxy=-480 MPa

Q: A vertical bar of length L with mass of 40 kg is rotated vertically about its one end at 40 rpm.…

A:

Q: 4.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: static equilibrium problem.We are given that the tension in cable A is 160 lb, and runs from a…

Q: 3.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: Q.1) Draw a Free Body Diagram for each object indicated below. Include values for known forces and…

A: (a) Draw the given diagram.

Q: The belt tensioner shown pivots about the point A and uses a spring to add tension to a belt. Given…

A: The belt tensioner shown pivots about the point A and uses a spring to add tension to a belt. Given…

Q: You are asked to analyze a catcher for a small drone. The catcher arm weighs 22 lb and is 8 ft long…

A: Given:To find:Reaction forces at A when the catcher arm stops.

Q: 4)→ For the figure below, find-the-coordinates-of-the-center-of-mass-of-the-rigid-frame-composed-of-…

A: Given:Rigid frame with length lTo find:Coordinates of centre of mass

Q: A horizontal board is held up by two supports. A cat sits on the end of the board, as shown. Find…

A:

Q: 1000 N 90 2000 N 90 1000 N 90 90 90° 130° 30 GG 12 m 12 m 12 m 1000 N

A:

Q: A shaft in equilibrium is shown below with dimensions as given in the table below: a b da dB dshaft…

A: Given data:

Q: A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the…

A: Given Length of the ladder = 10 m Weight of the ladder = 350 N Ladder angle = 30o Weight of the…

Q: Find the mass of a cube of edge a, if the density varies as the sum of the distances from three…

A: Consider a cube of edge a, now it is given that, ρ=k(x+y+z)                 where, k is the…

Q: Problem 4: Inputs: ● ● ● ● ● L₁ = 13 in L₂ = 11 in h = 10 in F = 40 lb 0 35° (measured from…

A: According to the question A force 40 lb at point C  We need to find  Reaction at point A and B

Q: Please give me the solution in a correct way. Don't use chatgpt

A:

Q: olve show full solution

A: To find:The principle stress at point A and absolute maximum normal stress at and absolute maximum…

Q: Solution please. Should 100% correct Each strut has a cross-section as shown in Figure Q5. Solve for…

A: Find the second moment of area about centroidal axis

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.