Need help. Please solve this and clearly state how you got your numbers and what formulas you used to solve it.   Please make sure you find all the 6 unknows please. Knowing the beta equals 30° and the solid plate weigh 100 kg. What is the cable tension T and the reaction forces at the two bearings? Assume bearing A is a thrust bearing but bearing B is notplease solve for the X component at bearing B. Again please also make you find all the 6 unknows please. And clearly indicate which is which. And please label and make sure to put units

Q: A motor supplies a constant torque M = 6 kN · m to the winding drum that operates the elevator. The…

A:

Q: magnitude of the moment MB given the moment MA. The connections at A and B are hinges. Assur MA =…

A: . tanθ=0.40.7θ=tan-10.40.7 θ=29.74°

Q: Find the magnitude of the compressive force acting on the gate shown in the figure and then…

A: Given:

Q: QUESTION 3 -50" B 50" A ♫ 11" 13" The bucket and its load have a combined weight of 4000 lb with…

A:

Q: a. Obtain the global stiffness matrix K of the assemblage shown in Figure 1 by superimposing the…

A: Node 1 and 4 are fixed The force at node 4 is

Q: 2. The system of figure has degrees of freedom. Fork Joint Two Three Four Spring Slider Five

A:

Q: The vector A is directed due west with a magnitude of 5 N. Vector B is directed due north with a…

A: As per given question  P=5N Q=12 We have to find value A+B

Q: I need a handwritten solution, Don't use chatgpt. Wrong solution will get downvote so carefully…

A:

Q: 1. Determine the distance x to the center of mass of the homogeneous rod bent into the shape shown.…

A:

Q: shaft k. disk -k,e J

A: Expressing the equation of torsional vibration system.

Q: Given the rod configuration shown with the applied torque, what compatibility condition is…

A: Two unknowns, only one equilibrium condition. In order to obtain solutions we need compatibility…

Q: ) In the Figure, the of ylinder A is 4m, cylinder Sm. Neglecting priction, a) solve radius is Gm,…

A: for the given system  rA = 4 m  rB = 6 m  rc = 5 m  To determine  (A) the reaction between A and B…

Q: ///////// with spring constants c 3

A: For this problem we are going to use stiffness matrix method. We have,  [K] [D] = [F]   where, K =…

Q: A.Draw a different configuration, and make it a diagram similar to Fig. 3. Specify each mass and…

A: (A) In different configuration, the masses attached through the ropes will be different and all…

Q: Find the slack-side tension on pulley A in N.

A: Solving Part A , we assume that torque is transmitted undiminshed

Q: 1. In lecture I focused on a horizontal mass-spring system so we could ignore gravity, but in…

A: Given: To find: Equation for the mass Equation for y' Force when y'=0 Total energy y and y'…

Q: rque Problem diagram below shows the lower leg being held in a stationary. The torque ng to turn the…

A: Angle made with horizontal = 50° Weight of leg WL = 90 N Weight of barbel Wb = 120 N Quadriceps…

Q: Q3 (Gyroscopes) The essential structure of a certain type of aircraft turn indicator is shown in the…

A: Given: The spring stiffness, K = 500 N/m The mass of uniform disk, m = 200 g = 0.2 kg The radius of…

Q: A shaft in equilibrium is shown below with dimensions as given in the table below: a b da dB dshaft…

A: Given data:

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

A:

Q: Assuming there is no axial thrust, find the reactions @ A ± C. Y Note: Force actlig on gear B is…

A: There is no axial forceAt gear B force is parallel to z axis At gear D force is parallel to y axis

Q: The 13m uniform rod as shown below weighs 1020 N. Segment AB and BC is 6m long. The cable acts at a…

A:

Q: C 2 m- Use the method of sections to calculate the axial force in members AC and BC. Enter your…

A:

Q: This portion of figure 3/8 from the text shows a Thrust-Bearing Support. The moments Mx and M₂ are:…

A: A thrust bearing is a type of bearing specifically designed to handle axial loads or thrust loads.…

Q: 8. Refer to figure 9. Given the following information: angles 0r= 20°, 02= 30°, 03= 41°, a 200 N…

A:

Q: Q6. What is the stress concentration for normal stress due to bending at the critical location?…

A: Option - D => 1.4

Q: The beam shown is supported by a Roller at C and is fixed to the wall at A. The beam has an internal…

A:

Q: R4-13. Determine the force P required to hold the 800-lb weight A by means of the system shown…

A:

Q: 3-17 A pair of ice tongs is shown in Figure P3-7. The ice weighs 50 lb and is 10 in wide across the…

A:

Q: 3. Consider the force system in equilibrium shown in the image below. Determine the following: a.…

A: To draw the free body diagram.

Q: Statics with Applications homework problem. Find the forces in the following members using any…

A: Statics with Applications homework problem.Find the forces in the following members using any…

Q: Find the equation of the following spring system. shaft kr -k,0 disk J

A:

Q: Q7. What is the stress concentration for shear stress due to torsion at the critical location?…

A:

Q: 3 digits behind comma From the given figure, F = 100 N. • Draw the FBD 1000 mm • Draw the action…

A: given data: F=100N AB=125mm BC=1000mm force at B?? force at A?? RAV=vertical force at point…

Q: Find the magnitude of the pressure force acting on the gate shown in the figure and then calculate…

A: Height of latch from the hinge = 4 ft Height of water column above the hinge = 3.6 ft

Q: - The bucket of a 'bobcat" is lifted and tilted by means of hydraulic cylinders EL and HJ Figure…

A:

Q: Help!!! Please answer Correctly !! Clearly solved Please !!!!!!!!

A:

Q: Find the rectangular components of the forces shown in figures P6-3

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: For number3 draw the diagram, wrong diagram is wrong 3. Find the equivalent spring constants if…

A: as per guidelines i have to solve only three subpart of your question

Q: Figure Q1c shows a bracket on rollers that allow the bracket to move along a beam in the horizontal…

A:

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

A:

Q: A 1-in, constant diameter shaft, is loaded with forces at A and B as shown, with ground reaction…

A: To findDetermine the factor of safety usingthe maximum shear stress failure theory.The distortion…

Q: Each cylinder weighs 50 lb and has a diameter of 20". Calculate all the reaction forces at the…

A: