The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V- belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=90ON), coefficient of friction u=0.3 4- the speed of large pulley.

The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V- belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=90ON), coefficient of friction u=0.3 4- the speed of large pulley.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Part A: Determine the force couple systems at points A-E. Part B: Draw a fee body diagram for points A-E.
PART 2: Determine whether the given mechanisms are Grashof's Chain, Non- Grashof's Chain or Transition chain using Grashof's criterion. Show your solution. 1. If: AB = 25 cm BC = 43 cm CD = 45 cm AD = 50 cm 2. If: AB = 1 ft BC = 1.8 ft CD = 2.4 ft AD = 3.5 ft D 3. If: AB = 6 in BC = 13.2 in CD = 21.1 in AD = 25.7 in
5. show all steps in detail, units and formulas please.
3 digits behind comma From the given figure, F = 100 N. • Draw the FBD 1000 mm F • Draw the action line of all forces that intersect in one point directly in the figure. Determine: 60° a) Force at smooth roll B b) Force at pin A Analytical solution. B. A 125 mm
Use Method of Sections to find the forces in members CF & CD.
Latch Gate 4ft Latches Water 3.6ft 8.0ft- Hinge Find the magnitude of the pressure force acting on the gate shown in the figure and then calculate its torque around the joint.
A 68.4 kg man stands on his toes by exerting an upward force through the Achilles tendon, as shown in the figure. Part (a) In units of newtons, what is the magnitude of the force through the Achilles tendon if he stands on one foot? Part (b) Calculate the force in units of newtons at the pivot of the simplified lever system shown. That force is representative of forces in the ankle joint.
Need help. Please solve this and clearly state how you got your numbers and what formulas you used to solve it. Please make sure you find all the 6 unknows please. Knowing the beta equals 30° and the solid plate weigh 100 kg. What is the cable tension T and the reaction forces at the two bearings? Assume bearing A is a thrust bearing but bearing B is notplease solve for the X component at bearing B. Again please also make you find all the 6 unknows please. And clearly indicate which is which. And please label and make sure it put units
DRAW ONLY THE FBD OR FREE BODY DIAGRAM FOR THE GIVEN FIGURE. COMPLETE FBD WITH LABELS. WRITE LEGIBLY OR TYPEWRITTEN FOR UPVOTE. NO UPVOTE IF INCOMPLETE
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. ( Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. ( A = 15°. C A 250 mm eeeeeee 900 mm k= 2.6 kN/m OB = 30° B LC 7-y 200 mm
Need help. Please solve this and clearly state how you got your numbers and what formulas you used to solve it. Please make sure you find all the 6 unknows please. Knowing the beta equals 30° and the solid plate weigh 100 kg. What is the cable tension T and the reaction forces at the two bearings? Assume bearing A is a thrust bearing but bearing B is notplease solve for the X component at bearing B. Again please also make you find all the 6 unknows please. And clearly indicate which is which. And please label and make sure to put units
Please ANSWER ALL of the given questions and show COMPLETE SOLUTION for each question. I will rate you with “UPVOTE/LIKE” if you answer every question with complete solution. I will rate you with “DOWNVOTE/DISLIKE”, if you don’t answer every question and it is incomplete solution. THANK YOU.