An ammonia compressor is driven by a 20 KW motor. The compressor and the motor RPM are 360 and 1750, respectively. The small sheave has a pitch diameter of 6 inches. If the belt to be used is standard B-120, determine the center distance between sheaves.

An ammonia compressor is driven by a 20 KW motor. The compressor and the motor RPM are 360 and 1750, respectively. The small sheave has a pitch diameter of 6 inches. If the belt to be used is standard B-120, determine the center distance between sheaves.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.46P

See similar textbooks

Related questions

Q: Two gears (A and B) are in mesh (they are interlocked) and both spin around their centers of…

Q: The offset slider-crank mechanism is driven by the rotating crank 2. Ro = 20 mm, R₂ 50 mm, R3 = 140…

Q: 8.9 Two-spur wheels each have 30 teeth of involute shape. The circular pitch is 25 mm. and the…

Q: Two cylinders rolling in the same direction has speed ratio of 2.5 and center distance of 50 cm.…

Q: Q4:- Two shafts A and B in the same straight line are geared together through an intermediate…

Q: Find the velocity at E..

A: Given: To find: Velocity at E

Q: A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear…

A: GivenTP=19NP=1640 rpmNG=480 rpmm=2.5 mmϕ=25ο

Q: The number of teeth on the driving sprocket chain is 50, used to change up of speed from 500 r.p.m.…

A: Introduction A chain is a dependable machine component that transfers power by tensile stresses and…

Question

An ammonia compressor is driven by a 20 KW motor. The compressor and the motor RPM are 360
and 1750, respectively. The small sheave has a pitch diameter of 6 inches. If the belt to be used is
standard B-120, determine the center distance between sheaves.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

In the mechanism shown, crank OA is the input and slider B the output. If OA = 5 cm, AB = 15 cm, and offset e = 7 cm, determine the pressure angle value that corresponds with the lowest quality of motion transmission. Write your answer in degrees but do not write the unit. B wee A X.
solve with solutions completeyly thanks
Analytically determine the linear displacement of the piston in the compressor linkage shown in the figure as the 45 mm. crank is rotated from its current position 90 degree clockwise.
solve using analytical way Given a single disk system that rotates as in picture. If: m₁ = 10 kg; R₁ = 15 cm; 0, 30°, m₂ = 15 kg; R₂ = 20 cm; 0₂ = 100°, m3 = 10 kg; R3 = 10 cm; θ3= 160° dan R₂ = 12,5 cm, calculated "me" and "θe"
solve a thru e show all steps
Analytically determine the linear displacement of the piston in the compressor linkage shown, as the 40 mm crank is rotated from its current position 60° counterclockwise. 40 mm 30⁰ crank 90 mm piston $1
Convert the following: (a) 400lbft to knm; (b) 6m/s to mi/h; (c) 20lb/in.2 to Pa; and (d) 500slug/in. to kg/m
Show your work! 1. A car travels 40 miles east, then turns southeast and travels for 35 miles at an angle of -65°. 31- a. Find the components of the second vector (the one at -65°). to obutingsm adi bat d b. What is the magnitude of the displacement from the original position? L 8x Atsuborq azoto tolgay and bri c. What direction is the car traveling in? (In other words, find the angle.)
This shoulder bolt is composed of hot-rolled monel. The head of the shoulder bolt is a regular hexagon and it measures 6 mm across opposite flats. The other dimensions of the bolt are given below, as well as the forces to which this component is subjected. Find the change in length of each segment of the part as well as the overall change in length from A to D F_A = 4.8 kN F_B = 5.1 kN F_C =1.6 kN F_D = 1.9 kN a = 4mm b = 4.1 cm c = 6.8 cm d_s = 5 mm d_t (effective) = 3mm Assume:∙ Bearing stress between threads of the bolt and the nut may be neglected∙ Stress concentration effects may be neglected∙ The force that the nut applies may be treated as a concentrated force.∙ The nut may be treated as rigid.∙ The forces applied to the nut and the shoulders of the bolt are distributed evenly around their perimeters δAB = δBC = δCD = δoverall =
13-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in Figure 13-39. 800 N 45° Figure 13-39 4. 30° 500 N
The figure shows a concept for a hand pump used for increasing oil pressure in a hydraulic line. Analytically determine the displacement of the piston as the handle rotates 12.5° counterclockwise. Also, input the corresponding initial and final vertical position of the piston the space provided. (Use 2 decimal places for the final answer.) 5" B 12° Offset 12° A 1.5" Initial Vertical Position of the Piston (inches) = 10.07 Final Vertical Position of the Piston (inches) = 8.45 DISPLACEMENT (inches) = 1.62
Please help