8.9 Two-spur wheels each have 30 teeth of involute shape. The circular pitch is 25 mm. and the pressure angle is 20°. If the arc of contact is to be 2 x pitch, determine the minimum addendum of the teeth.

8.9 Two-spur wheels each have 30 teeth of involute shape. The circular pitch is 25 mm. and the pressure angle is 20°. If the arc of contact is to be 2 x pitch, determine the minimum addendum of the teeth.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three Wheels. Three rubber wheels are mounted on axles so that they make tight contact with each other and their centers are on a line. The wheel on the far left axle is connected to a motor that rotates it at 35.0 r.p.m.; and drives the wheel in contact with it on its right which, in turn, drives the wheel on its right. The left wheel (Wheel 1) has a diameter of d₁ = 0.22 m, the middle wheel (Wheel 2) has d₂ = 0.32 m, and the far right wheel (Wheel 3) has d3 = 0.48 m. (a) If Wheel 1 rotates clockwise, in which direction does Wheel 3 rotate? (b) What is the angular speed of Wheel 3, and what is the tangential speed on its outer edge? (c) What arrangement of the wheels gives the largest tangential speed on the outer edge of the wheel in the far right position (assuming the wheel in the far left position is driven at 35.0 r.p.m)? (d) What is the largest tangential speed on the outer edge of the wheel in the far right position? (a) (b) Angular speed of Wheel 3: (c) Number Tangential speed…
i need the answer quickly
The diagram below shows a shaft with spur gear (B), bevel gear(D), and two supporting bearings (A and C). All dimensions are in millimeters and all shoulder fillets (at points where diameter changes) have a radius of . The pressure angle for the spur gear at B is . The pressure angle for the bevel gear at D is and the bevel angle is . Note that the shaft is designed so that only bearing A takes thrust. The shaft is made of steel with . All the critical surfaces are ground. The shaft rotates at . A motor with a power of is connected at the bevel gear through another bevel gear. This drives the shaft. A load is connected through another spur gear at the output spur gear at B. The standard deviation on the power is . (a) Determine the forces acting on the gears. Recall that for a spur gear, the relation between the tangential component of the force and the radial component of the force and the pressure angle is given by . For this bevel gear, the axial (thrust) component of the force on…
Three spur gear are arranged shown in the figure. Pinion A rotates for about 500 rpm. The three gears have a diametral pitch of 5. Number of teath and angle is shown in the figure. Determine the torque that each shaft is required to transmit and the resultant force on the shaft carrying the gear B. Draw the FBD of the figure.
Two parallel shafts are to be connected by spur gearing. The approximate distance between the shafts is 600 mm. If one shaft runs at 120 r.p.m. and the other at 360 r.p.m., find the number of teeth on each wheel, if the module is 8 mm. Also determine the exact distance apart of the shafts.
A recurring gear train composed of four sprockets 2, 3, 4, 5, has a value of the train of 1: 4 ½, being all the teeth of the gears of the same pitch. 2 has 40 teeth, 3 has 60 teeth. Find the number of teeth in 4 and 5. If the diametral pitch is 3, find the distance between the centers of the arrows. Answer N4 = 25; N5 = 75; 16.667 in
A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear will be rotating at a speed of 480 rpm. If the module of the pinion is 2,5 mm and pressure angle is 25 degree; Evaluate the outer diameter (mm) of the gear.
please help