A shaft turning 200 RPM is to drive another shaft at 250 RPM connected in open belt. Find the diameters of the two pulleys, using integral number of inches for each diameter, to give as nearly as possible a belt speed of 3500 FPM.

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: A 32-tooth pinion has a module of 3 mm, rotates 2400 rpm, and drives an 800-rpm gear. Determine the…

A:

Q: Find the design calculations of the gears box ,has (3)three speeds, Which is transmitted the power…

A: Given Data: The number of the tooth in gears are Z1=8, Z2=32 and Z3=64. The speed of 8 tooth gear…

Q: 1 to one module.

A:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: A commercial quadrotor drone for the photography industry uses a propeller system that uses gears.…

A: given; tooth of pinion (TP)=20diametral pitch (PD)=8mmspeen of pinion (NP)=2000rpm

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: The diameter of the smallest pulley = 2 in. Thus the maximum speed will be maximum at this pulley.…

Q: The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6 and…

A: Given data as per the question Speed of shaft =550 rpm No. of teeth on gear B =96 Diametral pitch =6…

Q: 8. Design a two-speed gearbox suitable to transmit 25kW. The input shaft runs at 530rpm and carries…

A: Given: The speed of gear D, ND = 215 rpm The input power, P = 25 kW The input speed, N1 = 630 rpm…

Q: The gearing arrangement suitable for this

A: Given; Determine gearing arrangement suitable for the given application. Where,  Power of motor=2.6…

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A:

Q: Problem Chain and Sprocket. A single-strand roller chain drive connects a 10-hp engine to a lawn…

A: Given DataN1=18 teethω1=1200 rpmω2=240 rpmP=10 hp ***As per company policy we are supposed to do…

Q: In the figure below, C and D represents brakes, which can be used to stop the rotation of either…

A: C represent gear 4  D represent gear 8 T denotes Teeth in this solution And N denotes rpm

Q: Please solve ellaborately and include the untis in every step, show diagram and write your solutions…

A:

Q: sin-D-d 20 V4C² - (D – d² D-d sin 20 Op

A:

Q: nism when annulus is i

A: introduction: we have to find out degree of freedom

Q: The number of teeth on pinion is

A: GIVEN ; A pair of spur gear;

Q: A rolling cone with a center angle of 15° turning at 240 rpm makes external contact with the second…

A: Given data: The Center angle of the first rolling cone is 2α=15°, The revolution of the first…

Q: 18. A wormgear set has a single-thread worm with a pitch diameter of 1.250 in, a diametral pitch of…

A: WORMGEARING DATA FROM PROB. 8-52:To=924 LB.IN.) MG-30rem FORCES: W+G=Wxw = To / (06/2) = 924 28-IN.…

Q: belt is on the steps either side of the center step. If the minimum speed is 40 rpm and the smallest…

A:

Q: Chain 8A having a pitch of 12.7 mm is used to connect 5 KW, 1400 rpm motor to a drilling machine.…

A:

Q: The gearing arrangement suitable

A: Given: A 1.5 kW motor is running at 1550 rev/min.so,  P=1.5 kW  Velocity=1550 rev/minIt is to be…

Q: gearing arrangement suitable for this

A: Given; A motor is running at; N= 1440 rev/minMotor power is given to run the motor is;  P= 1.5…

Q: Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal…

A:

Q: Find the chordal tooth thickness and chordal height at constant chord for a gear that has number of…

A: The contact always accurs at at two fixed point A and B hence AB=constant chordfrom the…

Q: A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear…

A:

Q: Draw the figure and show your solutions. PLEASE ANSWER IT ASAP FOR AN UPVOTE.   Shafts A and B are…

A:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: ic gear train suitable for lifting machine with the A is the mounted on the motor shaft and the load…

A:

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A: given data; ⇒teeth of pinion (Tp)=30⇒teeth og gear (TG)=50⇒module (m)=3mm⇒pressure…

Q: The number of teeth on pinion

A: Given; Determine the number of teeth on pinion ?Where,  A pair of spur gears with;Module, m=5…

Q: A straight tooth spur pinion has a 19 tooth pinion rotating at a speed of 1640 rpm. The driven gear…

A: We havem=DT2.5=D19D=47.5mmNow let P=Diametrical PitchP=TDP=1947.5P=0.4

Q: A pair of spur gears with module 5 mm and a center distance of 450 mm is used for a speed reduction…

A: given: A pair of spur gearsmodule, m=5 mmcentre distance=450 mmSpeed reduction=5:1

Q: A gear set consists of a full depth 20-tooth pinion driving a 40- tooth pinion. The module of the…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.