The number of teeth on the driving sprocket chain is 50, used to change up of speed from 500 r.p.m. to 850 r.p.m. Find the number of teeth on the driven sprocket. If the pitch circle diameter of the driven sprocket is 350 mm and center to center distance between the two sprockets is 1000 mm, determine the pitch and length of the chain.

Q: (B) Two shafts A (driver) and B (driven) in the same straight line are geared together through an…

A:

Q: Determine the setting for a straight spur gear having 46 teeth of module 4 mm.

A: Given Data⇒ Straight spur gear : Number of teeth(t)=46 teeth Module(d)=4 mm

Q: The drawing represents a planetary reduction gear used in aeronautics. Calculate the speed of the…

A: Speed of motor: N3=1200 rpm and considering N1=0 (is fixed) Number of teeth: Z1=50 teethZ2=18…

Q: taper angle and the set over respectively are

A: Given data,  Length of the shaft,L= 90 mm Tapered portion length,TL=55 mmD=80 mmd= 65 mm Determine…

Q: in a planetary gear train, the arm C caries two gears A and B and a compound gear D-E. The gear A…

A:

Q: A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth.…

A:

Q: The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The…

A:

Q: The center distance between the two gear is 250mm and module is 5cm. Find the number of the teeth of…

A: module=diameter/teeth

Q: 1 to one module.

A:

Q: In an epicyclic gear of the sun and planet' type has a fixed outer wheel A, sun wheel S rotates at a…

A: GivenTP=27TS=18Ns=600 rpm

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: 6. Consider the gear system given below where b is the gap between width of the teeth and empty…

A: Concept: 1) Given gears system is simple Spur Gear Train.  2) Driving gear rotates with required…

Q: 2. Shafts A and B are connected by rolling cones and are turning in the same direction. A makes…

A: A shaft is a spinning machine element with a circular cross-section that is used to convey power…

Q: Sun gear-'2' rotates at 500 rpm and arm '6' rotates at 750 rpm both in clockwise AS viewed from…

A: Given: The speed of sun gear 2, N2 = 500 rpm(CW) The speed of arm, x = 750 rpm (CW)

Q: Two meshing ge ocity ratio Moc I, e=2 Pressure angle

A:

Q: Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and…

A: The diameter of the smallest pulley = 2 in. Thus the maximum speed will be maximum at this pulley.…

Q: Problem 2. 2000 rpm. Calculate the output The gear train shown below has an input speed nimput speed…

A:

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: 8.10 Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in…

A: Given: Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed (N)=750rpm Power=4.6kW…

Q: consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number…

A:

Q: Two equal involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angle are in mesh.…

A: According to the given data Number of teeth (T)=40 Module (m)=3mm Pressure angle ϕ=20° Speed…

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A:

Q: Question 1 A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4…

A:

Q: UUSigned to reduce the speed of the wheel as shown The information of the gears is also listed Motor…

A: Given: D=2 inch N1=3000 rpm V=24 ft/min

Q: belt is on the steps either side of the center step. If the minimum speed is 40 rpm and the smallest…

A:

Q: Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal…

A:

Q: Find the chordal tooth thickness and chordal height at constant chord for a gear that has number of…

A: The contact always accurs at at two fixed point A and B hence AB=constant chordfrom the…

Q: Draw the figure and show your solutions. PLEASE ANSWER IT ASAP FOR AN UPVOTE.   Shafts A and B are…

A:

Q: Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200…

A: For the given epicyclic gear train let C.W. direction be positive and C.C.W. direction be negative.…

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: An epicyclic gear consists of ring gear, planet gear and sun gear. The ring has 72 internal teeth…

A:

Q: The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating…

A: For the solution refer below images.

Q: A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an…

A:

Q: A simple gear train of 30 and 40 teeth for pinion and gear wheel respectively is used to drive an…

A:

Q: 60 teeth 90 70 teeth в 85 teeth

A:

Q: Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal…

A: Given data :-Universal coupling axis angle = 60°Find out :-(1) Greatest and smallest values of the…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.