The box wrench is subjected to the P = 74 lb force. (Figure 1) Determine the principal stresses at point B on the cross section of the wrench at section a-a. Express your answers in kilopounds per squared inch to three significant figures separated by a comma. -Η ΑΣΦ 01.02 = Submit Part B Request Answer Op₁. Op = Ivec -Π ΑΣΦ Specify the orientation for this state of stress. Express your answers in degrees to three significant figures separated by a comma. Ivec ? www. ksi ?

The box wrench is subjected to the P = 74 lb force. (Figure 1) Determine the principal stresses at point B on the cross section of the wrench at section a-a. Express your answers in kilopounds per squared inch to three significant figures separated by a comma. -Η ΑΣΦ 01.02 = Submit Part B Request Answer Op₁. Op = Ivec -Π ΑΣΦ Specify the orientation for this state of stress. Express your answers in degrees to three significant figures separated by a comma. Ivec ? www. ksi ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve all. Both Questions Please.
Parvinbhai
Determine the required diameter (in inches) of rod ACif the allowable normal stress is 23.44 ksi and P = 6.6 kips. Round off the final answer to four decimal places.
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
Only handwritten and correct pls
Parvinbhai
Illistrate Mohr's circle for the given plane stress state. Including the coordinates of the points, show the points with the faces of the figure, the center of the circle and the magnitude of the radius. 7. 3kPa 5kPa 1kPa
Determine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!
Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 Ib 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please I =
The state of plane stress at a point with respect to the xy-axes is shown in Fig. (a). Using Mohr's circle, determine (1) the principal stresses and principal planes; (2) the maximum in-plane shear stress; and (3) the equivalent state of stress with respect to the x'y'-axes. Show all results on sketches of properly oriented elements. y20 MPa 50° 40 MPa 16 MPa (a)
Draw For the state of plane stress shown below, determine the principal stresses, the maximum in- plane shear stress and the average normal stress; and show the stresses on properly oriented elements. 413 ks - 1.8 ksi 灣彩

The 0.91-in.-diameter rod in (Figure 1) is subjected to the loads shown. Figure 9 in. 200 lb 300 lb 3 in. 1 of 1 1200 lb Part A Determine normal stress o at point A. Express your answer in kilopounds per square inch to three significant figures. σA = Submit Part B ||| ΑΣΦ | 11 Request Answer Submit Previous Answers vec Answer Requested ? Determine shear stress Tzz at point A. Express your answer in kilopounds per square inch to three significant figures. (Tzz) A = 5.47 ksi ksi