A cylindrical rod 360 mm long, having a diameter of 10.0 mm, is to be subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.9 mm when the applied load is 22500 N, which of the four metals or alloys listed below are possible candidates? Justify your choice(s). Material Modulus of Elasticity (GPa) Yield Strength (MPa) Tensile Strength (MPa) Aluminum alloy 70 255 420 Brass alloy 100 345 420 Copper 110 210 290 Steel alloy 207 450 550

Q: An aluminum alloy cylinder with a diameter of 3 in. and a height of 6 in. is subjected to a…

A:

Q: In the figure below, a stainless steel wire is supporting a weight, W. The Yield Strength and…

A:

Q: The stress-strain relation of an aluminum alloy bar having a length of 2 m and a diameter of 10 mm…

A: Calculate stress by using the following equation: σ=Pπ4d2 Here, Load applied on the rod is P and…

Q: Draw a typical stress-strain behaviour of steel subjected to tension. On the graph, show the modulus…

A:

Q: 2. An aluminum alloy specimen with a radius of 0.28 in. was subjected to tension until fracture and…

A: The solution is given below:

Q: An aluminum alloy cylinder with a diameter of 76 mm and a height of 150 mm. is subjected to a…

A:

Q: 2. The tensile link shown is flat, is 5 mm. thick, and carries an axial loac a. Compute the maximum…

A: GIVEN- Axial load (P)=1350 N Thicknesss (t)= 5 mm

Q: Two bars of different materials and same size are subjected to the same tensile force. If the bars…

A: Given data: Unit elongation =δLδ1Lδ2L=25

Q: A steel bar 4 inches long and having a square cross section 0.8 inches on an edge is pulled in…

A:

Q: A 8 mm radius Steel is subjected to tensile test. Determine its yield and and ultimate load it can…

A: The ultimate load and yield load can be calculated using the yield stress and ultimate stress. The…

Q: A tensile test is carried out on a steel rod of 14mm radius and gauge length of 140 mm. The yield…

A: Tensile test is carried out to draw the stress strain curve of the steel.  The given data is:…

Q: A tension stress of 70 ksi was applied on a 12-in. long steel specimen. Determine the resultant…

A: It is required to determine the resultant elongation. Here, lo is the original length, E is the…

Q: Sample: Malleable Steel (AISI 4145) Original Diameter: 6.14mm Gauge Length: 55 mm Final Length:…

A: Given data, Original diameter D = 6.14 mm Gauge length L = 55 mm

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

A: Answer Based on the given data, we can calculate the minimum Elastic Modulus required for possible…

Q: A tensile load of 150kN is applied to a round metal bar with a diameter of 16mm and a gage length of…

A: Find a.) Modulus of elasticity (MPa)b.) Poisson's ratio for this metal

Q: To stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads…

A:

Q: An aluminum alloy cylinder with a diameter of 76 mm and a height of150 mm. is subjected to a…

A:

Q: TABLE P3.19 Specimen No. Carbon Content (%) 1 2 3 0.2 0.5 0.8 Deformation (mm) Load (kN) 0.00 0.07…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: A tensile test was done on a steel specimen with the gauge length of 525 and a stress of 175 MPa. If…

A:

Q: 1. Titanium alloy with an elastic modulus of 107 GPa (15.5 x 106 psi) and an initial diameter of 3.8…

A:

Q: For a bronze alloy, the stress at which plastic deformation begins is 280 MPa, with modulus of…

A:

Q: Situation No. 2 A bronze bar is fastened between a steel bar and an aluminum bar as shown below.…

A:

Q: A No. 8 steel rebar is tested in tension. By monitoring the load reading of the testing machine, it…

A:

Q: Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch…

A: Given,   width of bar, t =0.750 inmaximum axial stress, σmax=7670 psib=2.50 ind=2×14 in=2×0.25 in

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

A:

Q: An aluminium wire (E=10,600 ksi) having a diameter d%-1/8 inch. and length L=14 ft is subjected to a…

A:

Q: Find the maximum force (kN) that a 2.5 mm thick and 50 mm wide nickel strip, having a yield strength…

A:

Q: A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus…

A: Yield Strength: It is defined as the stress that a material can withstand without any permanent…

Q: An ASTM A615 grade 60 number 10 rebar with a gauge length of 8 in. was subjected to tension to…

A: It is required to determine the stress in the rebar. Here, P is the load and A is the area of the…

Q: A 1-cm-diameter, 30-cm-long titanium bar has a yield strength of 345 MPa, a modulus of elasticity of…

A: Solution-