A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa ents Allowable compressive stress 140 MPa 70 MPa ces ents Which of the following most nearly gives the load, in percent, carried by the copper? Ssors Select the correct response ication 44.44% Niki 55.56% Blogs 66.67% Courses 33.33%

A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa ents Allowable compressive stress 140 MPa 70 MPa ces ents Which of the following most nearly gives the load, in percent, carried by the copper? Ssors Select the correct response ication 44.44% Niki 55.56% Blogs 66.67% Courses 33.33%

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the total deformation on the brass. Steel Brass Copper Est = 200 GPa 12(10-)/°C apr Ebr Ecu 17(10-)/°C 120 GPa 100 GPa %3D ast = 21(10-6)/°C acu Acu = 515 mm? |Ast 200 mm2 Abr = 450 mm2 300 mm -200 mm 100 mm O -0.0109mm O 0.0241mm O -0.0241mm O 0.0109mm oooO
The critical bending compressive stress in the extreme fibre of a structural steel section is 1000 MPa. It is given that the yield strength of the steel is 250 MPa, width of flange is 250 mm and thickness of flange is 15 mm. As per the provisions of IS: 800 -2007, the non-dimensional slenderness ratio of the steel cross-section is (a) 0.25 (c) 2.00 (b) 0.75 (d) 0.50
A mild steel bar of 2cm is subject to tensile test. The bar yields under a load of 80kN. It reaches a maximum load of 150kN and breaks finally at a load of 70kN. Estimate the a) Average tensile stress at yield point b) ultimate tensile stress c) average stress at the breaking point if the diameter of the fractured neck is 1cm
A steel specimen is tested in tension. The specimen is 2 in. wide by 2.3 in. thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 30 kips and fractured at 40 kips. a) Determine the tensile stress at yield and fracture; b) If the original gauge length was 4 in., estimate the gauge length when the specimen is stressed to 2 the yield stress.
The assembly is composed of a steel shell and an aluminum core that has been welded to a rigid plate. The gap between the plate and the aluminum is initially 1- mm. If the assembly's temperature is reduced by 180°C, determine (a) the final axial stresses in each material and (b) the deflection of the rigid bar. To support your response, draw a deformation diagram with appropriate labels. Use the following properties: Aluminum core Steel shell Diameters (mm) d = 15 mm do = 30 mm d₁ = 20 mm E (GPa) 70 200 2 m a (/°C) 22 x 10-6 12 x 10-6
Condition #1:E A structural support for a machine is subjected to a static compression load of 20 kN. The support is manufactured from a circular rod made from SAE 1040 Hot Rolled steel. Specify suitable diameter for the cross section of the rod based on the basic size. Steel data are available in Table A-10 from the textbook. Condition #2: The same structural support of the basic size determined in Condition 1 is subjected to a tensile load of 15 kN that is repeated several thousand times over the life of the machine. This load is not an addition to the 20 kN. Specify a suitable steel that is suitable to this application based on the basic size determined in Condition #1. Loading of Condition #1 does not apply here. Condition #3: The same structural support from Condition 2 is heated from room temperature of 25°C. The support is placed inside a frame on both ends. There is a total clearance of 0.2 mm between the support and its frame. Initial length of the rod is 200 mm. Specify the…
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
3. Discuss the ff property of steel: -Uniformity -Elasticity -Permanence -Ductility -Toughness -Corrosion -Fatique Principles of Steel Design (Civil Engineering)
After an inspection it is found that a structural ceramic part has no flaws greater than 100 micrometers in size, calculate the maximum service stress (in MPa) available with SiC. Assume that Y= 1
Given: metal specimen x-section (circular) = 0.5sin Gaye length Fractured final final diameter Determine ^ = 2.030 In occured at 28, 500 # length = 2.30in dia = 0.43 in al Ultimate b7 Elongation c) Reduction tensile stress in ksi a percentage as of x-section area as a percentage
A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m by applying a pure moment 'M'. If E is 200 GPa, then magnitude of the pure moment 'M' will be