Find the maximum force (kN) that a 2.5 mm thick and 50 mm wide nickel strip, having a yield strength of 310 Mpa and a tensile strength of 430 Mpa, can withstand with no plastic deformation. Round off your answer to the ones place

Task (3) you are asked to perform tensile test on specimens of two different materials (A and B) and you obtained the stress-strain diagram of the two specimens as shown in Figure 2: 400 350 300 250 Material A 200 150 100 50 0.02 0.04 0.06 0.08 0.1 0.12 0.14 0.16 0.18 Strain (mm/mm) 50 Material B 30 20 10 0.02 0.04 0.06 0.08 0.1 Strain (mm/mm) Figure 2: Tensile Test Analysis Stress (MPa) Stress (MPa)

At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; a = 12.5 x 10-6/°F] bar with a width of 3.0 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; a = 9.6 x 10-6/°F] bar with a width of 2.0 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine (a) the lowest temperature at which the two bars contact each other. (b) the normal stress in the two bars at a temperature of 250°F. (c) the normal strain in the two bars at 250°F. (d) the change in width of the aluminum bar at a temperature of 250°F. (1) 3.0 in. 32 in. 2.0 in. B ↓ (2) 44 in. 0.04-in. gap Determine the lowest temperature, Tcontact, at which the two bars contact each other.

Question 5 A steel component is subjected to a biaxial state of stress in which both stresses are tensile in nature, and having magnitudes 100 and 60 MPa. The plane at which the resultant stress has maximum obliquity with the normal (in degrees) is

A steel 0.6 inch×1.2 inch steel 90 m long is subjected to a 45 KN tensile load along its lenght.If poison's ratio is 0.3 Find: A. The deformation along its lenght. B. The deformation along its thickness. C. The defirmation along uts width. D. The lateral strain.

A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of this material is 210 GPa and Poison's Ratio is 0.3. The change in width after applying a tensile force of 150 kN is?

A mild steel bar has a gauge length of 80 mm and the total elongation is 0.08 mm, find the strain produced in it.

At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.5 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.7 in. and a thickness of 0.75 in. The supports at A and C are rigid. Assume h1=2.5 in., h2=1.7 in., L1=31 in., L2=46 in., and Δ=Δ= 0.04 in.  (A) Determine the lowest temperature, Tcontact, at which the two bars contact each other. (B) Find a geometry-of-deformation relationship for the case in which the gap is closed. Express this relationship by entering the sum δ1+δ2, where δ1 is the axial deflection of Bar (1), and δ2 is the axial deflection of Bar (2). δ1+δ2= _____in. (C) Find the force in the Bar (1), F1, and the force in Bar (2), F2, at a temperature of 225oF.  By convention, a tension force is positive and a compression force is negative. IN KIPS (D) Find σ1 and σ2,…

(b) (i) A tensile test specimen made from 0.4% C steel has a circular cross section of diameter d mm and a gauge length of 25 mm. When a load of 4500 N is applied during the test, the gauge length of the specimen extends to 25.02 mm. If the Young's Modulus of the steel is 199 GPa, calculate the diameter of the tensile test specimen used. 4

The shown figure represents the stress-strain relations of metals A and B during tension tests until fracture.Determine the following for the two metals (show all calculations and units):a. Proportional limitb. Yield stress at an offset strain of 0.002 in./in.c. Ultimate strengthd. Modulus of resiliencee. Toughnessf. Which metal is more ductile? Why?