A 1-cm-diameter, 30-cm-long titanium bar has a yield strength of 345 MPa, a modulus of elasticity of 110.3 * 10^3 MPa, and Poisson's ratio of 0.30. Determine the length and diameter of the bar when 2224N load is applied

A 1-cm-diameter, 30-cm-long titanium bar has a yield strength of 345 MPa, a modulus of elasticity of 110.3 * 10^3 MPa, and Poisson's ratio of 0.30. Determine the length and diameter of the bar when 2224N load is applied

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

CN=44
For a tensile test it can be shown that the percent cold work (%CW) is related to strain according to the following relationship: %CW = () × 100 E+1 Using this equation, compute the percent cold work experienced by naval brass (for which the stress-strain behavior is shown in the Animated Figure 6.12) when a stress of 400 MPa (58020 psi) is applied. %CW
A No. 8 steel rebar is tested in tension. By monitoring the load reading of the testing machine, it was found that the specimen yielded at a load of 60,000 lbs and fractured at 75,000 lbs. Determine the following: a. Tensile stresses at yield and at fracture. b. Estimate how much increase in length would occur at 75% of the yield stress in a 16-in. gauge length.
Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch radius hole centered on its width, as shown in the sketch. With an axial load, P = 8650 lbs applied, the maximum axial stress at the edges of the hole was experimentally determined to be 7670 psi What is the stress concentration factor, K, of the hole? 1.33 0.75 1.66 1.50 P 2.50 in. -Radius 1/4 in. P= 8650 lbs
A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and a diameter of 0.38 inches the rest. If it is subjected to a tensile load of 6,000 lbs, what will be the tótal deformation of the bar if it has a modulus of elasticity E= 28.5 x 10^6 psi. %3D O 0.1378 inches O 0.1338 inches O 0.1352 inches O 0.1364 inches O 0.1423 inches
An aluminium wire (E=10,600 ksi) having a diameter d=1/8 inch. and length L=14 ft is subjected to a tensile load P. If the maximum permissible elongation of the wire is 1/6 inch and the allowable stress in tension is 10 ksi, what is the allowable load Pmax? Answer in Ibs
A prismatic aluminum bar has cross-sectional dimensions 40 x 60 mm and a length of 350 mm. The modulus of elasticity is 70 GPa and Poisson's ratio is u=0.35. When an axial load of 100 kN is applied, the proportional change in the bar's volume is
8. If the modular ratio is equal to 11, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
If Poisson's ratio is 0.42, the Modulus of rigidity is 70.4225 GPa, and the bulk modulus is 416.66 GPa, then the elastic modulus of elasticity is (3 Points) 300 GPa 300 MPa 200 MPa None 200 GPa
Please solve fast!
1. The tensile strength vs. temperature curves of aluminum are plotted below. Explain the meaning of these two curves. 400 Ultimate strength 300 Yield strength 200 100 -200 -150 -100 -50 50 100 150 200 250 Temperature, °C Strength, kPa
The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0 04 0.08 0.12 0.16 0.20 0.24 0.28 0 0005 0.0010.0015 0.002 0.0025 0.0030.0035