A chromatographic analysis is performed with a sample containing toluene and benzene. The column length was 25 m and the flow rate 45 mL/min. Solute tr air 1.75 benzene (A) 7.00 1.85 toluene (B) 16.10 1.65 Calculate the theoretical plate height for each peak. Benzene: 109 mm/plate and Toluene 16 mm/plate Benzene: 105 mm/plate and Toluene 49.7 mm/plate Benzene: 172 mm/plate and Toluene 175 mm/plate Benzene: 119 mm/plate and Toluene 181 mm/plate

A chromatographic analysis is performed with a sample containing toluene and benzene. The column length was 25 m and the flow rate 45 mL/min. Solute tr air 1.75 benzene (A) 7.00 1.85 toluene (B) 16.10 1.65 Calculate the theoretical plate height for each peak. Benzene: 109 mm/plate and Toluene 16 mm/plate Benzene: 105 mm/plate and Toluene 49.7 mm/plate Benzene: 172 mm/plate and Toluene 175 mm/plate Benzene: 119 mm/plate and Toluene 181 mm/plate

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

What is 4c?
Diprivan® (propofol) is a commonly used sedative-hypnotic agent used for sedation and anesthesia during minor as well as major surgical procedures. It is a liquid preparation administered through the IV route of drug administration. Based on what you see below, this prep is most likely a(an): Emulsion Microemulsion Suspension Solution
A mixture of three components is separated using paper chromatography, and each component is analyzed using absorption. With standards containing 100 ppm of each component run simultaneously, the following data were obtained: cmpd A, 0.72 absorbance; B, 0.55; C, 0.80. For the unknown mixture, the data obtined when run under identical conditions were as follows: cmpd A, 0.15 absorbance, B, 0.84; C, 0.75. a) Calculate the relative percentage composition of the unknown mixture. b) The distances traveled by the three components were 8.5, 6.3, and 5.5 cm, respectively. Sketch the appearance of the paper chromatogram. Label each spot. c) Calculate the Rf values if the solvent front is 18 cm.
Scientists determined the %w/w H20 in methanol by GC, using a capillary column coated with a nonpolar stationary phase and a TCD detector. A linear regression gives a relationship between %w/w H20 (x) and Peak Height (y) as follows: y= 89.71 x- 0.3024 Calculate the %w/w H20 in a sample giving a peak height of 4.23. O A. 0.0379 O B. 0.0505 O C. 379.17 O D.0.0472 O E. 0.0438
An unknown was found to contain 10.80 ug of analyte per liter. A spike of 4.30 ug/L was added to a replicate portion of unknown. Analysis of the spiked sample gave a concentration of 15.10 pg/L. Find the percent recovery of the spike. % recovery = If the acceptable recovery is specified to be in the range from 96 to 104%, is the recovery of the spike acceptable? yes no hulu 山T四回

please help me find average and standard deviation
I have set up my spreadsheet and was able to reproduce the result with a pKa of 4.64. TRUE OR FALSE
Answers po sana for letters D, E & F
A solution containing orange rind extract was analyzed using gas chromatography to measure its limonene content. The parameters used to analyze the standards and samples are listed below. Calculate the concentration of limonene in the solution in ug/mL
You perform a concentration of a single component using displacement chromatography, and the following data applies: Concentration of binding sites: 4*10^(-4) M Kd for displacer: 2.0*10^(-5) M Kd for component A: 4*10^(-5) M Kd for component B: 1.5*10^(-4) M The concentration of the injected displacer is 2.0*10^(-4) M Determine and justify whether the components are part of a displacement system, and if so, provide their free and bound concentrations. Assume that the number of binding sites is the same for all components.
A chromatographic column was found to have the following constants: A= 0.01 cm, B= 0.30 cmis and C=0.015s. What are the optimum flow rate? A none of the choices Bp-15 cmis p-45 cm/s D u-3.6 cmis E-26 cm/s
From the data calculate : a) the number of plates from each peak b) the mean and the standard deviation for N c) the plate height for the column