A 3-phase short circuit fault at point E in a plant with single line representation below. consists of. Draw the impedance diagram pu of the system and calculate the short circuit current that will occur. calculate. (Ubaz 33 kV, Sbaz 10 MVA, take the voltage source as 1 pu) Uk: %8 5 MVA 33/15 kV Xd"=%12 Uk=%16 15 MVA 10 MVA over heo d line 10 kV A 10/33 kV B C D cable G1 TR1 TR2 havai hat 20 km. %2 6 km. Z=(0,12+j0,08)Q 1 pu Z=(0,18+j0,27)Q

A 3-phase short circuit fault at point E in a plant with single line representation below. consists of. Draw the impedance diagram pu of the system and calculate the short circuit current that will occur. calculate. (Ubaz 33 kV, Sbaz 10 MVA, take the voltage source as 1 pu) Uk: %8 5 MVA 33/15 kV Xd"=%12 Uk=%16 15 MVA 10 MVA over heo d line 10 kV A 10/33 kV B C D cable G1 TR1 TR2 havai hat 20 km. %2 6 km. Z=(0,12+j0,08)Q 1 pu Z=(0,18+j0,27)Q

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q.3 When a line-to-ground fault occurs, the current in faulted phase 'a' is 100A. The zero-sequence current in phase 'c' is r
3.8. Three identical 9-MVA, 7.2-kV/4.16-kV, single-phase transformers are con- nected in wye on the high-voltage side and delta on the low voltage side. The equivalent series impedance of each transformer referred to the high-voltage side is 0.12 + j0.82 S per phase. The transformer supplies a balanced three- phase load of 18 MVA, 0.8 power factor lagging at 4.16 kV. Determine the line-to-line voltage at the high-voltage terminals of the transformer.
I need the answer as soon as possible
Single line to ground fault of a solidly grounded generator positive sequence current is j2.5 p.u, then the current flow in the neutral during the fault is O j1.05 p.u O jo.25 p.u O j2.5 p.u O j7.5 p.u
(Q.2) For the following network, calculate the fault currents (IF1, IF2, IF3 and IF.) in pu and in kA, and fault MVA (ie. short-circuit level) at the indicated locations. Internal reactance of generators are j0.9 pu. Base quantities: 11 kV, 400 MVA on the generator side. 113.3 kV 4 MVA, 7% j0.5 2 j0.4 2 300 A 200 A 11 KV 250 MVA
B1
(b) A 30000 kVA, 13.8 kV generator with X = 18% is connected to a bus which supplies two identical motors as shown in the Figure 2. The subtransient reactance X of each motor is 25% on a base of 6000 kVA, 7 kV. The bus voltage at the motors is 7 kV when a three phase fault occurs at the point P. For the fault specified, determine (a) the subtransient current in the fault (b) the subtransient current in breaker A and (c) the symmetrical short circuit interrupting current in the fault and in breaker A. юю DO A P 0-0 Gen. Figure 2 Motors
A 15 MVA, 6.6 kV, wye connected generator has X 1 = X 2 = 20%and X 0 = 10%. The neutral of the generator is groundedthrough a reactor of 5% reactance based on the generatorrating. A double line-to-ground fault occurs at terminals band c. What is the current in the ground?
Q. when a three-phase fault occurs at 75% of the distance from bus G. This fault has 10 arc resistance. 100 MVA, 115 KV Line GH a-Assume that the angle of the mho characteristic is 70°.Determine if the zone I mho unit at H set for 90% of the line GH can operate for this fault. b-Determine the apparent impedance seen by the distance relays at H for this fault. G Z, = 0.365 Z83° - 80% l6 = 1.96 Z–31.42° 4 = 2.60 Z–47.76° ķ = 4.51 Z-40.68° All values in per unit on 100 MVA, 115 kV.
In the shown below power system, both generators G1 and G2 emf’s are equal.All the system data are shown on the system diagram.a) Draw the system diagram in per unit using (MVA)base = 75 and (KV)base =20 KV in the generators side.b) Calculate the three-phase balanced short circuit current (If) at busbar 3 inAmpere and the fault level (MVA)sc in MVA.c) If the fault at busbar 3 is a line-to-line fault, calculate the fault current inAmpere and the fault level (MVA)sc in MVA.
In a 3-phase, 4 wire unbalanced system, the current in neutral wire is 18 A. The magnitude of zero sequence current is ?