8-18. Determine the vertical displacement of joint C ifmember CD is fabricated 10 mm too long.4mDEBC

Answered: Image /qna-images/answer/677b8ee3-416c-47e6-b48e-b039d27258e6.jpg

Answered: 8-18. Determine the vertical…

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter8: Engineering Materials

Section: Chapter Questions

Problem 85CQ

See similar textbooks

Similar questions

A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
Verify the value of Zx for a W1850 that is tabulated in the dimensions and properties tables in Part 1 of the Manual.
For the beam shown: (a) determine the distance a for which the maximum positive and negative bending moments in the beam are equal; and (b) draw the corresponding shear and bending moment diagrams for the beam.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Use an elastic analysis and compute the extra load in the weld (in kips per inch of length) caused by the eccentricity.

Recommended textbooks for you

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

8-18. Determine the vertical displacement of joint C if member CD is fabricated 10 mm too long. 4m D E B C