*7-44. The plastic block is subjected to an axialcompressive force of 600 N. Assuming that the caps at thetop and bottom distribute the load uniformly throughoutthe block, determine the average normal and average shearstress acting along section a-a.600 N150 mm50 mm50 mm 50 mm600 N

Given: The axial compressive force acting on the horizontal plane is F1=-600 N The inclination of…

Answered: *7-44. The plastic block is subjected…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed loading along its length which is 0 at x= 0 and 9 kN/m at x= 1.5 , and to two concetrated loads Determine the average normal stress in the bar as a function of x for 0 <_x < 0.6m
The bar has a 80 mm by 20 mm rectangular cross section. If P = 90 kN, determine the normal stress magnitude acting on surface a-a. 80 mm 62° a P = 90 kN
Determine the shortest distance d to the edge of the plate at which the force P can be applied so that it produces no compressive stresses in the plate at section a–a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness.
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
Q1/ The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading that increases linearly from w = 0 at x = 0 to w w, at r = a, and then decreases linearly to w 0 at x= 2a, determine the average normal stress in the bar as a function of x for a
The bent shaft is fixed in the wall at A. If a force F is applied at B (the force is acting on the plane parallel to the x-o-y plane). Take F = 54 N and 0 = 45°. 1. Determine the internal forces acting on the section containing points D and E 2. Determine the normal stress component acting at point E 3. Determine the shear stress component developed at point E 4. Draw the state of stress on a volume element (stress element) located at point E 5. Determine the principal stresses acting at point E by constructing Mohr's circle A 150 mm E 200 mm 30 mm 75 mm B F
*3-12. Fiberglass has a stress-strain diagram as shown. If a 50-mm-diameter bar of length 2 m made from this material is subjected to an axial tensile load of 60 kN, determine its elongation. σ (Pa) 300(10%) 1/2 €(mm/mm)
The steel pipe is filled with concrete and subjected to a compressive force of 75 kN. Determine the average normal stress in the concrete due to this loading. The pipe has an outer diameter of 60 mm and an inner diameter of 50 mm. E_s=200 GPa, E_c=24 GPa
The solid circular rod has a cross-sectional area of 450 mm². It is subjected to a uniform axial distributed loading along its length of w= 7 kN/m. Two concentrated loads also act on the rod: P = 4 kN and Q = 6 kN. Determine the normal stress in the rod at x = 1.3 m. Assume a = 0.5 m and b = 1.0 m. W B x a P b
Q1/ Two spanners are used to tighten the pipe. If P =200 N is applied to each spanner, determine the maximum torsional shear stress developed within regions AB and BC. The pipe has an outer diameter of 25 mm and inner diameter of 20 mm.
The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, np = 0.4.
The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading along its length of w 8 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 6 kN. Determine the normal stress in the rod at x = 1.5 m. Assume a = 0.7 m and b = 1.2 m. W ->P Q A B x a Answer: 0 = i MPa b

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

*7-44. The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps at the top and bottom distribute the load uniformly throughout the block, determine the average normal and average shear stress acting along section a-a. 600 N 150 mm 50 mm 50 mm 50 mm 600 N