*8-28. The support consists of three rigid plates, which are connected together using two symmetrically placed rubber pads. If a vertical force of 5 N is applied to plate A, determine the approximate vertical displacement of this plate due to shear strains in the rubber. Each pad has cross-sectional dimensions of 30 mm and 20 mm. G₁ = 0.20 MPa. C 40 mm A 5 N B 40 mm

*8-28. The support consists of three rigid plates, which are connected together using two symmetrically placed rubber pads. If a vertical force of 5 N is applied to plate A, determine the approximate vertical displacement of this plate due to shear strains in the rubber. Each pad has cross-sectional dimensions of 30 mm and 20 mm. G₁ = 0.20 MPa. C 40 mm A 5 N B 40 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The force P at D causes the rigid bar CBD to rotate by 0 = 0.5°. The flexible cable AB was unstretched before the application of the force. Determine the normal strain in the cable and the horizontal displacement of point D. A 16" D B C -0-- 12" 12" P
SN = 79 kips
Verify that whether function (let a>0) can be used as stress function. If so, try to find the stress component (without force) and draw the force distribution on the plate as shown. b/2 Þ= a(xy² + x³) 6/2
The head H is connected to the cylinder of a compressor using six 316-in. diameter steel bolts. If the clamping force in each bolt is 800 lb, determine the normal strain in the bolts. If sY = 40 ksi and Est = 2911032 ksi, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released?
The steel shaft has a radius of 50mm. Determine the torque (T) applied to the shaft if the two strain gages attached to the shaft surface record the deformations ex -80 (10-6) and ey ' : = 80 (10-6). Take E = 200 GPa, v = 0.3. | 45° UT
F=150lb a=6in bd=8in
Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB Originally the cable is unstretched. Part A If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00485 mm/mm, determine the displacement of point B Express your answer to three significant figures and include appropriate units. AB= μA Value CE ? Units B A 800 mm 600 mm
*3-12. Fiberglass has a stress-strain diagram as shown. If a 50-mm-diameter bar of length 2 m made from this material is subjected to an axial tensile load of 60 kN, determine its elongation. σ (Pa) 300(10%) 1/2 €(mm/mm)
Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi.
The A-36 steel post is subjected to the forces shown. If the strain gages a and b at point A give readings of Pa = 300(10-6) and Pb = 175(10-6), determine the magnitudes of P1 and P2.
The metal stud punch is subjected to a force of 120 N on the handle. determine the magnitude of the reactive force at the pin A and in the short link BC. Also, determine the resultant internal loadings acting on the cross section at point D.
Determine the normal strains at the point associated with the x and y axes. Determine the shear strain at the point associated with the x and y axes. Determine the normal stresses at the point associated with the x and y axes. Determine the shear stress at the point. Determine the normal stress that acts along an axis rotated at θ= 45° counterclockwise from the positive x-axis.