Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. Originally the cable is unstretched. ▼ Part A AB = HÅ If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00484 mm/mm, determine the displacement of point B. Express your answer to three significant figures and include appropriate units. Value wwwww Units 600 mm ? B 800 mm

Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. Originally the cable is unstretched. ▼ Part A AB = HÅ If a force is applied to the end B of the member and causes a normal strain in the cable of 0.00484 mm/mm, determine the displacement of point B. Express your answer to three significant figures and include appropriate units. Value wwwww Units 600 mm ? B 800 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

hi please solve this question. (Mechanical )
Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional Area Modulus of Elasticity AB 1,400 mm2 200 GPa BC 1,800 mm2 200 GPa DB 1,400 mm2 200 GPa BY 18KN A 400mm 400mm 400mm 55.00° 55.00°
Determine the shear stress of the cylinder pivot pin (φ25mm). The clamping force of the pliers is 6000N. The dimensions of the structure are: X1 = 10 mm X2 = 120 mm Y1 = 110 mm Y2 = 798 mm Use the units [N, mm], ie the answer comes in MPa !!! Please enter a numeric value only !!
You need the shear modulus for a particular material in order to calculate shear strain for a known applied shear shear stress. You can't find shear modulus for the material, but you can find elastic modulus (200 GPa) and Poisson's ratio (0.3). Which of the following could you use as the shear modulus for your calculations? 200 GPa O 60 GPa O 77 GPa O 154 GPa
2. ! SHOW FULL SOLUTION ! * use THERMAL STRESS AND STRAIN FORMULAS *use DATA GIVEN BELOW
solve all 3
Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions at the wall of the cantilever are provided. L1= 14.00 ft L2 = 7.75 ft Vc = 87.00 kips Mc = 621.875 kip-ft 20 kips 70 kips 12 kips/ft 6 kips/ft Mc A В L1 L2 99.00 kips O 110.00 kips O 75.00 kips O 64.00 kips O 87.00 kips
Can you please help me with question 2. Thank you.
6. Airplane components often have a “stressed skin" construction, which consists of a thin sheet of aluminum in tension connected to the structure with rivets (i.e. pins that go through circular holes). a. If the aluminum skin is subject to a far-field biaxial tension of σ = 100 MPa and has a yield strength of σ = 210 MPa, will the rivet cause the sheet to yield? b. What is the strain through the thickness (z-direction) at the top-most edge of the hole? What does this mean is happening to the plate at that point? c. If a crack of length a = 1 mm forms at the side of the hole, will the plate fracture? How about if the crack is a = 3 mm? Take the aluminum to have a fracture toughness of K₁c = 15 MPa√m, and take the geometric stress concentration factor to be Y = 1.12. 50 = a
Parts A B C shown in pictures
Question 7 Determine the maximum shear force in kN in the figure below. 10 kN/m 25 kN • m A E B C D 1 m 1 m 3 m 2 m
Strains measured in a, b and c directions are yardımıa=-150x10-6, ɛb=200x10-6, and ɛc=300x10-6 with the help of the rosette placed at point A of the elastic material under the effect of plane tension. Calculate the principal stresses since the modulus of elasticity in the material is E= 200 GPa and the Poisson ratio ν= 0.3