450 mm, B 19 500 mm C 360 mm 320 mm 600 mm X

Q: plane diagram: Also String 1 String 1 B String 2 A The diagram above shows Carts B and C which roll…

A:

Q: 4.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: acting along line b-b.We can resolve the force F into its x and y components using the following…

Q: In (Figure 1), set Fy-300 N. igure H 60 F₁-500 N 1 of 1 > Part A Determine the magnitude of the…

A:

Q: 6. show all steps in detail, units and formulas please.

A:

Q: Three forces are applied to a screweye as depicted on the figure and table of parameter values.…

A:

Q: Please find the Grashof classification and the Barker classification of the two four-bars: (NOTE:…

A: Grashof's law- In the case of only the four-bar mechanism, to sum of the length of the shortest and…

Q: Bicycle Physics Given: F = 60 lbs R₂-8 in R-5 in R₂-2 in Re-14 in Calculate F₂ T₂ F₂ T₂ F₂ T₂ F₂ T₂…

A: Write the given data. F1=60 lbsR1=8 inR2=5 inR3=2 inR4=14 inCompound Gear ratio=R1R2×R3R4

Q: | Blocks D and E have mass of 4 kg and 6.4 kg, respectively. Take x = 2 m. (Figure 1) Figure D B -6…

A: Blocks D and E have a mass of 4 kg and 6.4 kg, respectively.Take = 2 m. To Find-The distance s for…

Q: A team of professional thieves wants to knock down a castle wall using a primitive explosive. At…

A: Given: total mass of the explosive(M) = 40 Kg and it breaks into three pieces as shown below:

Q: The design below is used for a bridge construction. All parts of the assembly are made of ASTM A36…

A: P = 4000 lbOD = 4.5 inL = 20 inTo find:Resultant force (fR)

Q: Unit: BTU HL = Heat loss (BTU)= Hv x hours If loss for one day, H = 24 hrs If we are talking about a…

A: Heat loss (HL) per day through a single building element =  AreaArea (A)Resistance (R)×∆T×24 hours…

Q: A2.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: Write the expression, in Excel notation, that you would type into cell 86 to determine the…

A: Springs, follow the Hooke's law. It states that the Force(F) needed to extend a spring through a…

Q: Determine the magnitude and coordinate direction angles of the resultant force. 0.75 m FAR = 250 N…

A: Given, FAC = 400 N FAB = 250 N

Q: The coefficient of friction everywhere is 0.30. If max force P at static equilibrium is 55N, find…

A: Solution: Considering the weight acts at the midpoint of the ladder, then Considering static…

Q: Required information A rope connecting points A and B supports the force F shown in the figure.…

A: Given data: L=8 ftF=12 lb Need to determine the unit vector of B to A.

Q: Don't Use Chat GPT Will Upvote

A:

Q: Calculate the 1st moment of area and 2nd moment of area for the shape below. The dimensions are…

A:

Q: As shown in figure a Pepsi can and a plastic Pepsi bottle. Describe how they were manufactured

A: Pepsi can is produced using an ample material found in the world's covering. It happens normally in…

Q: A Portable Crane will be designed as shown in Figure which is able to withstand dynamic loads. The…

A:

Q: A guy who works out at your gym found out that you are an engineer and has hired you do an analysis…

A: Data given-

Q: Suppose a piece of solid lead weighing 41.3 g at a temperature of 312 °C is placed in 413 g of…

A: To determine:The temperature after the thermal equilibrium is reached given:The mass of the solid…

Q: If 1 Pa is equal to 145 psi, what algebraic equation is needed to find out how many MPa there are in…

A: Given that,  1 Pa = 145 psi So, 1 psi = (1/145 ) Pa So, x psi = (x/145) Pa....... This is algebraic…

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.