2-The crimping tool is used to crimp the end of the wire E. If a force of 20 lb is applied to the handles, determine the average shear stress in the pin at A. The pin is subjected to double shear and has a diameter of 0.2 in. Only a vertical force is exerted on the wire. 20 lb !!! OROD 1.5 in. 2 in. 1 in. 5 in- 20 lb

2-The crimping tool is used to crimp the end of the wire E. If a force of 20 lb is applied to the handles, determine the average shear stress in the pin at A. The pin is subjected to double shear and has a diameter of 0.2 in. Only a vertical force is exerted on the wire. 20 lb !!! OROD 1.5 in. 2 in. 1 in. 5 in- 20 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the required diameter of the pins at A and B if the allowable shear stress for the material is tallow = 100 MPa. Both pins are subjected to double shear.
The beam is constructed from three boards. Determine the maximum loads P that it can support if the allowable shear stress for the wood is tallow = 400 psi. What is the maximum allowable spacing s of the nails used to holdthe top and bottom flanges to the web if each nail can resist a shear force of 400 lb?
Q2/ The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. Ea = 70 GPa, Emg = 45 GPa, Ga = 26 GPa, Gmg = 17 GPa. 50 mm 30 mm
All the pins are in double shear, and they each have a diameter of 14 mm. The average shear stress in each pin CANNOT exceed 70 MPa. What is the max magnitude of P that the beam can support
The shear diagram visually represents the shear forces to which a bar is submitted. Considering the structure below, CONSTRUCT the shear diagram and DETERMINE what is the maximum magnitude of the shear force suffered by this bar. ALTERNATIVES 1.0 kN 14.5 kN 15.5 kN 19 kN.m 28 kN
Urgently required
If the pin at C has a diameter of 5 mm and is subjected to double shear, the maximum average shear stress, in MPa, is P B
1. Determine the Tavg in the pins at A, B. and C. Pin A is under double shear and pins B and Care under single shear. Each pin has a diameter of 10 mm. B 45 60° 60 mm 5 kN 50 mm
P = 93.3 N Determine the force at F. Take it apart to help you solve
Only Handwritten solutions are allowed. No Chatgpt, you must have to draw the free body diagram.
A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever is P = 395 N, determine the shear force applied to the shear key. 42 mm. ↓ Shear key O 10.90 KN O 18.31 KN O 9.70 KN O 14.25 KN O 13.17 kN 700 mm C Shear key detail
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 17 kN applied at A. Assume a = 330mm, b = 150mm, c= 75mm, and 0 = 40°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 24 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F₂ Support bracket b MPa F₁ Answers: Tpin B = i Ob= i a MPa