1-32. Determine the largest intensity w of the uniform loading that can be applied to the frame vithout causing either the average normal stress or the average shear stress at section b-b to exceed ở =15 MPa and T = 16 MPa, respectively. Member CB has a square cross section of 30 mm on each side. 4m 3m B

Q: An axial load P is supported by the short steel column shown in the figure. The column has a…

A: Given that, Axial load = P Cross-sectional area of column = Acolumn=13,300 mm2 Allowable average…

Q: dy = m y2 dx

A:

Q: ength than A

A: introduction: here we find is the statement is false or true

Q: a) Find the overall efficiency of the system shown below as a function of the two individual…

A: To Find : a) The overall efficiency of the system.Given : The Higher temperature is The…

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: I have three parts that need to be answered pertaining to the print provided below.   What size…

A: The size of the print provided in the title box is C.Hence the correct answer is C.

Q: y h с b bh .1

A:

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: shown in Fig. 2-13.2a. The inscribed grid with each square having a length of 1 ft locates each…

A:

Q: Define the following phrase; i. External forces ii. 111. iv. V. Forces generated by motion Forces…

A:

Q: FRONT VIEW

A: According to the details provided in the question, we need to calculate ISOMETRIC VIEW

Q: 350 lb 30 250 lb

A:

Q: d W Pm a Ps

A: The free body diagram of the system is showing below –

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: 100 mm 100 mm 10 mm 10 mm. 200 mm 100 mm f 10 mm I II

A: For the selection of sections, we have to calculate the maximum bending stress in the beam. From the…

Q: choose the correct answer 200 B. G- A Zero Force members

A: We know that if a joint with two members is not subjected t any external load and also that joint…

Q: Question 6 Classify the following parts, giving reasons for your answers: (a) A speed indicator for…

A: **As per our company we are supposed to do only 3 sub part if you need the rest please upload that…

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: Wheels of an airplane are made of

A: Solution:

Q: y (x- 6y)dx - x (2x - gy) dy = 0; x =1 , y = 1

A:

Q: 2015.2 2.4713 27 0.031 2182.4 3.4800 29.33 0.044 2416.9 4.9900 32.48 0.063 2693.1 7.5062 36.19 0.095…

A: Given Data  To find “Since you have posted a question with multiple sub-parts, we will solve the…

Q: メオyー4)dx -(3x -プ-4)dy NHEN メ=4iY -1

A: (x+y−4) dx−(3x−y−4) dy=0 , when  x=4  then  y=1 (x+y−4)dx−(3x−y−4)dy=0⟺(x+y−4)dx+(y−3x+4)dy=0…

Q: Write F if True and T if False. Oxygen is the most abundant and dominant gas in the Earth’s…

A: Answer: T

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: 57. In gas welding process, rubber is used as preferred material for hoses. Select one: True False

A:

Q: - 2- 45 100lbs/ft 300lb 30 200lbs

A:

Q: what is the unit of stress?

A: stress can be defined as the ratio of the applied and the cross-sectional area.

Q: thế časting part whose perspective pictures are given below, take into account the surface of the…

A: COVE DESIGN

Q: find the length of (20mm) diameter bore is equal to that in the (30 mm) diameter bore,

A:

Q: Answers: FA= FB = i i kN kN

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.