Q1/The prismatic bar has a cross-sectional area A. If it issubjected to a distributed axial loading that increaseslinearly from w = 0 at x = 0 to w w, at r = a, and thendecreases linearly to w 0 at x= 2a, determine the averagenormal stress in the bar as a function of x for a

TO DETERMINE: The average stress as the function of x. GIVEN: area A Load wo length 2a DIAGRAM:

Q1/ The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading that increases lincarly from w 0 at x 0 to w = w, at x a, and then decreases linearly to w =0 at x 2a, determine the average normal stress in the bar as a function of x for a

Q1/ The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading that increases lincarly from w 0 at x 0 to w = w, at x a, and then decreases linearly to w =0 at x 2a, determine the average normal stress in the bar as a function of x for a

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.14P: The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind...

See similar textbooks

Similar questions

2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The boom supports the two vertical loads, F, : = 800 N and F2 = 350 N. Neglect the size of the collars at D and B and the thickness of the boom. (a) Determine the average normal stress in the 20 mm diameter cable BC. 4 (b) Determine the average shear stress in the 10 mm diameter pin A. (c) Suggest an appropriate diameter for cable BC if it is made from material having tensile yield stress of o, = 250 MPa. 1 m B 1.5 m D. F2 30° A F,
The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this thickness such that d = 150 mm. Plot the distribution of normal stress acting along section a–a.
The solid circular rod has a cross-sectional area of 450 mm². It is subjected to a uniform axial distributed loading along its length of w= 11 kN/m. Two concentrated loads also act on the rod: P = 2 kN and Q = 2 kN. Determine the normal stress in the rod at x = 0.8 m. Assume a = 0.4 m and b = 1.1 m. A →x a Answer: 0 = i B W P -- b MPa
The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm and P acts along the centerline of this thickness such that d = 50 mm. Plot the distribution of normal stress acting along section a-a.
The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial distributed loading along its length of w = 8 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 7 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.2 m. A -> a Answer: 0 = i B W b C MPa Q
Do neatly
Need Step wise solution
The vertical force P acts on the bottom of the plate having a negligible weight. Determine the shortest distance d to the edge of the plate at which it can be applied so that it produces no compressive stresses on the plate at section a-a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness. a 200 mm- d 300 mm a 500 mm
The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial distributed loading along its length of w = 9 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.5 m. Assume a = 0.7 m and b = 1.3 m. A B MPa x a Answer: 0 = i b
The tube has an inner diameter d; = 20 mm and an outer diameter d, = 22 mm. It is subjected to an internal pressure of 1 MPa and the loads shown below. Determine the stress at point A and draw it on a stress element. 200 mm 400 mm 150 N-m 600 N 1500 N 800 N
X a W -P B b Q The solid circular rod has a cross-sectional area of 330 mm2. It is subjected to a uniform axial distributed loading along its length of w = 8 kN/m. Two concentrated loads also act on the rod: P = 2 kN and Q = 3 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.1 m. Answer: 0 = MPa