Determine the maximum normal stress in the bar. The diameter is 1.5cm.F1 = 7KN F2 = 6KN F3 = 2KN F1 = 9KN FDCВAF1F2F3F4

Answered: Image /qna-images/answer/95586bfa-5950-4cdb-b5d6-012a5ea54a9b.jpg

Answered: Determine the maximum normal stress in…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bar is connected to the support using a pin having a diameter of d =lin. If the allowable tensile stress for the bar is (o,)low = 20ksi , and the allowable bearing stress between the pin and the bar is (0,)allow = 30ksi , determine the dimension w and t so that the gross area of the cross section is wt = 2in² and the load P is a maximum. What is this maximum load? Assume the hole in the bar has the same diameter as the pin. (Hint: Use the prjjected area whenj calculating the bearing stress.) t d w/2 w/2
1-103. The bar is supported by the pin. If the allowable tensile stress for the bar is (o)allow = 150 MPa, and the allowable shear stress for the pin is Tallow = 85 MPa, determine the diameter of the pin for which the load P will be a maximum. What is this maximum load? Assume the hole in the bar has the same diameter d as the pin. Take 1 = 6 mm and w = 50 mm.
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 20 kN applied at A. Assume a = 270mm, b = 170mm, c = 70mm, and 9 = 50°. Pin B is in a double-shear connection and has a diameter of 24 mm. The bell crank has a thickness of 36 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 2 decimal places. F₁ Bell crank Support bracket Add your answer B b 4
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths.
The steel bracket is used to connect the ends of two cables Part A O max = If the applied force P= 1 kip, determine the maximum normal stress in the bracket Assume the bracket is a rod having a diameter of 2.25 in Express your answer to three significant figures and include appropriate units. Value Units 4 in. ? P
Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.
Problem #3: Determine the shear strain yry at corners A and B if the plastic distorts as shown by the dashed line. 12 mm 4 mm 8 mm 3 mm 300 mm 2 mm D |A -400 mm- 5 mm using = new
An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20 mm 20 mm 5 mm 5 mm Steel core E = 200 GPa Brass shell E = 105 GPa 250 mm Determine the normal stress in the brass shell. The normal stress in the brass shell is MPа.
If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress developed on the cross section of the supporting member at section a- a, where L= 700 mm, and the radius r= 30 mm. Section a - a 98.089 MPa O 49.564 MPa 8.665 MPa 96.009 MPa O 96.945 MPa O 97.049 MPa
Determine the principal stresses in the cantilevered beam at points A and B.
The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed loading along its length which is 0 at x= 0 and 9 kN/m at x= 1.5 , and to two concetrated loads Determine the average normal stress in the bar as a function of x for 0 <_x < 0.6m
The solid 0.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 500 lb/ft. Two concentrated loads also act on the rod: P = 1900 lb and Q = 900 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN F2 = 6KN F3 = 2KN F1 = 9KN