- 2014-T6 Aluminum 304 Stainless -C 86100 Bronze steel 12 in. 8 in. B C| 4 in. 4 ft - 6 ft- 3 ft

Q: Problem 8. The assembly has the diameters and material make-up indicated. If it fits securely…

A: To find: The average normal stress in each material and also find the longitudinal displacement of B…

Q: how do we know these values if they're not given

A: Below is the answer to your query.

Q: The five-bolt connection must support an applied load of P = 1500 lb. If the average shear stress in…

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: The cylindrical tank with a spherical endcap has an outer radius of 2 m and a wall thickness of 25…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: how can we determine these values if not given in the problem?

A:

Q: Determine the average normal stress developed in rod AB if the load has a mass of 50 kg.  The…

A:

Q: The three rods are made of A-36 steel and form a pin-connected truss as shown. The assembly is…

A:

Q: 8-7. The rigid pipe is supported by a pin at A and an A-36 steel guy wire BD. If the wire has a…

A: As per the Bartleby policy, I am solving first question only

Q: The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two…

A:

Q: The 0.35-inch-diameter cylinder is made from C83400 red brass and is placed in the device depicted…

A: inlet diameter (d)= 0.35 inch  Temperature (T1)= 50 F other diameter ( D)= 0.10 inch

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: The wheel on a trolley is held in place on the leg using a 5-mm-radius pin. If the wheel is…

A: The problem is asking for the average shear stress in the pin. Shear stress is a measure of how much…

Q: 1-103. The bar is supported by the pin. If the allowable tensile stress for the bar is (o)allow =…

A:

Q: The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the…

A: For Am 1004-T61 magnesium                 αmg=26×10-6/°CEmg=44.7 × 103MPa For 304-stainless-steel…

Q: The yoke-and-rod connection is subjected to a 15 tensile force of 5 kN. Determine the average normal…

A:

Q: A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure…

A: A spherical gas tank has an inner radius of r = 1.5 m.If it is subjected to an internal pressure of…

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal…

A: To find out the centroid…

Q: At a temperature of 20 °C there is a gap ∆ = 0.2 mm between the lower end of the brass bar and the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.