If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress developed on the cross section of the supporting member at section a- a, where L= 700 mm, and the radius r= 30 mm.

Q: Member CBCB has a square cross section of 30 mmmm on each side. Determine the largest intensity www…

A:

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: Determine the state of stress at point A on the cross section of the pipe at section a–a. Show the…

A:

Q: The two rods support the vertical force of P = 40 kN. Determine the normal stress in rod AB and AC…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: 1-32. Determine the largest intensity w of the uniform loading that can be applied to the frame…

A: For the solution refer below images.

Q: The solid circular rod has a cross-sectional area of 420 mm². It is subjected to a uniform axial…

A:

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: If the allowable tensile stress for wires AB and AC is sallow = 200 MPa, determine the required…

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the…

A: Given: The magnitude of the force applied on the handles is FH=100 N. The length and breadth of the…

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: The beam is supported by a pin at C and by a short link AB. Each pin has a diameter of 20 mm. Assume…

A: Length of the link BCAngle made by link AB from the horizontal:Diameter of each pinSo the area of…

Q: The bar has a cross-sectional areao of 490(10-6)m2. It is subjected to triangular axial distributed…

A: Area of the cross section  To determine:The average normal stress in the bar

Q: If the load has a weight equivalent to 5 kN, determine the maximur hormal stress on the cross…

A: Given Data Load is :P=5 kN=5000 N Radius of circle is :r=2 cm=20 mm Distance of CD is : LCD=50…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.