2. A strut in a space frame has a rectangular cross section of 10.0 mm by 30.0 mm. It sees a load that varies from a tensile force of 20.0 kN to a compressive force of 8.0 kN. Stress Ratio For each of Problems 1-9, draw a sketch of the variation of stress versus time, and compute the maximum stress, minimum stress, mean stress, alternating stress, and stress ratio, R. For Problems 6-9, analyze the beam at the place where the maxi- mum stress would occur at any time in the cycle.

2. A strut in a space frame has a rectangular cross section of 10.0 mm by 30.0 mm. It sees a load that varies from a tensile force of 20.0 kN to a compressive force of 8.0 kN. Stress Ratio For each of Problems 1-9, draw a sketch of the variation of stress versus time, and compute the maximum stress, minimum stress, mean stress, alternating stress, and stress ratio, R. For Problems 6-9, analyze the beam at the place where the maxi- mum stress would occur at any time in the cycle.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.26P: The figure shows the FBD of a portion of the space truss shown in Fig. P5.25. Use this FBD to find...

See similar textbooks

Similar questions

6.10 - This is a statics problem that deals with ‘Zero-Force Members’.
Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 4 answers is correct
Determine the member force BC in the truss below using the method of joints List the member force as either tension compression. 20kN 5m 2m 7m 28kN C 28kN T 20kN C 20KN T
Do not round off intermediate values when using them to solve subsequent values; however, they may be written up to 4 decimal places in the answer sheets. Final answers should be rounded off up to 4 DECIMAL PLACES. Box the final answers.
Please answer the problem completely. Show a free body diagram. Final answers: 1st section: 166.67 mPa 2nd Section: 55.56 mPa 3rd Section: 122.22 mPa
For the structure loaded as shown in Fig. P-4-6.6, find the horizontal and vertical components of the pin force at B as they act upon member CD
Warren truss and a series of moving loads are shown in Figure 2. Assuming the loads can travel in either direction along the center of the truss. i) Draw the influence line for the force in member FC. ii) Calculate the maximum force (tension or compression) that can develop in member FC due to series of moving loads which acts along the bottom chords of the truss.
2) The figure shows a truss which is pin connected at C and supported by a roller at D. It carries the vertical loads of 200 kN and 100 kN at joints A and E, respectively. Use the Method of Joints. a) Calculate the force in member DE. b) Calculate the force in member BE. c) Calculate the force in member BC. 4 m B 2 m 200KN tookN
Draw all forces acting on member ABEG here: A B E O GO
The following trusses are subjected to loads of P₁ = 70 kips and P2 = 5 kips at the joints P1 as shown below. These simulate a semi-tractor trailer and a car. Calculate the forces in each member of the truss. Use a force summary diagram to display the results.
2. A steel strut, 40 mm diameter, is turned down to 20 mm diameter for one-half its length. Calculate the ratio of the extensions in the two parts due to axial loading.