1. A 600-V, 150-HP, 600 r.p.m. d.c. series motor has an armature and series field resistance of 0.120 and0.040, respectively. The full-load current is 200A.(a) Find the back e.m.f. at full-load.(b) Find the armature developed power and torque at full-load.Ans. [568V, 1808.13 N.m]

Answered: 1. A 600-V, 150-HP, 600 r.p.m. d.c.…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 240 V series motor develops a torque of 120 Nm at a speed of 900 rpm. The armature winding resistance is 0.20 and the series field winding resistance is 0.1 Q. For a constant load torque find the new speed of the motor when a diverter resistance of 0.1 Q is placed across the series field winding.
Please question 5 solution
A 5HP 230V 1500 rpm shunt motor has an armature resistance including brushes of 0.175 ohm, the shunt field resistance is 610 ohms and the stray losses equal to 305W. The input at rated load is nearest to: a. 4250 W b. 4050 W c. 4350 W d. 4150 W
A 250 V series motor has an armature resistance of 0.2 ohm and a series-fieldresistance of 0.18 ohm. If the speed is 6oo RPM when the current is 32 amps.What will be the motor speed when the load is reduced so that the current is18 amps, under which condition the percent flux change is 50 % of the percentcurrent change.
Please question 4
2. A 2-pole, 50 Hz induction motor supplies 15 kW to a load at a speed of 2950 rpm. a. What is the motor's slip? b. What is the induced torque in the motor in N-m under these conditions? c. What will be the operating speed of the motor be if its torque is doubled? d. How much power will be supplied by the motor when the torque is doubled?
A four-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. If the dc-to-ac converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.
A 1200 rpm, 700V Series DC motor has an armature resistance of 20 and the field resistance of 90. If the rotational losses is 450W and the efficiency is 71% , the output power of the motor in Kwatt is
(b) A 2 pole 220 V, 100A, and 850 rpm separately excited DC motor has an armature resistance of 0.15 0. Two field coils are connected in parallel and used to drive a load with the torque of TL = 400 – 0.2N, Nm Where N is the motor speed in rpm. Armature voltage control and two field windings connected in series are used in speed control below and above the rated, respectively. (i) Calculate the motor armature current and speed when the armature voltage is reduced to 110VV. (ii) Examine the motor speed and current when field coils are connected in series.
I:01)
A 4-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert 400 Volts DC into a set of 3-phase AC voltages. Find the frequency required for the AC voltages assuming that the slip is 4 percent. The load requires 2 hp. If the DC-to-AC converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the DC source.
The armature current of a series motor is 60 A when on full load. If the load is adjusted so that this current decreases to 40A,find the new torque expressed as a percentage of the full load torque. The flux for a current of 40A is 70% of that when the current is 60A.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

1. A 600-V, 150-HP, 600 r.p.m. d.c. series motor has an armature and series field resistance of 0.120 and 0.040, respectively. The full-load current is 200A. (a) Find the back e.m.f. at full-load. (b) Find the armature developed power and torque at full-load. Ans. [568V, 1808.13 N.m]