L04-report-sheet

F Xp Side View To Xg gauge Top View The gauged beam of length 0.33 (m) and cross section base 0.013 (m) and height 0.017 (m) shown is made of aluminum with a modulus of elasticity of 69 (GPa) and an ultimate strength of 300 (MPa). A strain of 250 (microstrain) is measured from the gauge which is 0.18 (m) from the wall in the x direction. What is the magnitude of load at of the end of the beam in units of Newtons?

Topic: Calculation of stretch: small es. finite deformation Consider the mapping in 2-D only 21 = X1 +7X2 = X1+ u1 82 = (1+e)X2 = X2 + Uz. (1) 1. In terms of y and a compute F, i.e. the Fij's and then compute the Cj = FF.j; recall F = Fi. Now do the following. %3D 2. Take two fibers, viz. dX = e and dY = e2, that is two fibers of unit length along the ej and ez axes, respectively in the reference state. Compute the stretch of dX and dY. 3. Compute the small strains from this mapping with u = 7X2 and ur = eX¡ from above. What would these small strains suggest for the change in lengths of dX and dY? 4. Comment on what you found from the results of 2. and 3. You may want to sketch the deformed state to explain your comments.

O 2 O 3 O 4 V= 7L V= 7L V= 7L V= 7L T= 100K T= 500K T= 300K T= 700K P= ? P= ? P= ? P= ? Note: Each "dot" represents one gas particle. a. What variables are held constant? volume b. Which container do the particles have the most KE? 1 4. c. Which container has the lowest temperature? 1 4 d. Which container has the lowest pressure? 1 2 3 4 e. Which container has the highest pressure? 1 4. f. What gas law does the above relationship represent? What kind of relationship does this represent(direct or indirect)? L Display Settings O Focus 3:49 PM 2/26/202 F12 tist prt sc

Please answer allquestions

Need hep with this Q.

G Mas x P Acce x Hat x Hat × | Md: × 45c × Rep × Cha × |V. Try × ULT ש Sol x New x Mda x | session.masteringengineering.com/myct/itemView?assignmentProblemID=18323525&attemptNo=1&offset=prev ssignment 1D (CHAPTER 5) - Attempt 1 Problem 5.58 Consider the hatch door in (Figure 1). Figure P 2 m 79°F Partly cloudy 2 m B 1 of 1 Q Search Part A Determine the force in the cable as a function of 0, needed to support the 100-kg hatch door. Express your answer in terms of 8. ΕΠΙ ΑΣΦ $1 ? vec δ E 77 Ꮎ K λ μ V 元 P T X W W A Σ Ф Ψ Ω h E P= 981 cos 0 Submi Previous Answers Request Answer X Incorrect; Try Again; 9 attempts remaining DB 25 N

Please answer all questions

C 4) The Wire C The Wire BC X C 4) The Wire x C The Wire BC X The Wire BC x C 4) The Wire x G 3.) With an b Homework A Mi unidad + A drive.google.com/drive/u/0/my-drive Update : A Drive Q Buscar en Drive - Nuevo With an initial diameter of 10 mm, an A-36 steel wire is connected at m ends B and C. The weight of bar AB is negligible along with any friction Mi unidad in the pins. The area contraction of wire BC cannot exceed0.0028%. Compartido What is the mass of the heaviest possible uniform cylinder supported as shown in the figure? Recientes 4x Destacados Papelera Almacenam 62.3 GB de 100 GB utilizado(s) Comprar almacenamier Archivos 10:11 PM hp 4/19/2021

Needs Complete typed solution with 100 % accuracy.

Please. Answer parts please. Attempt Once. Use cosine and show in rad and degree (2 diff eq)

Im not sure how ro go about this, can you help me figure out these answers or how to get these answers?

MOMENTS (Engineering Mechanics)

rod-fleet02-xythos.content.blackboardcdn.com/5e0164771d151/9050980?X-Blackboard-Expiration=1645941600- | D Page view A Read aloud |O Add text Draw Name: Banner ID: 1) In Gotham City, the departments of Administration (A), Health (H), and Transportation (T) are interdependent. For every dollar's worth of services, they produce, each department uses a certain amount of the services produced by the other departments and itself, as shown in Table 1. Suppose that, during the in Health services, and $0.8 million in Transportation services. What does the annual dollar value of the services produced by each department need to be in order to meet the demands? year, other city departments require S1 million in Administrative services, $1.2 million Table 1 Department A H. T $0.20 0.10 0.20 0.10 0.10 0.20 Buy H. 0.40 0.30 1. 0.20

Do not provide handwritten solution,Maintain accuracy and quality in your answer,Take care of plagiarism,Answer completely,You will get up vote for sure.

PLEASE ANSWER NUMBER 14.MECH 221-KINEMATICS: PLEASE GIVE DETAILED ANSWER AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.

Distilled water at 10deg C stands in a glass tube of 9.0 mm diameter at a height of 24.00 mm. What is the true static height in mm if the surface tesnsion is 0.0742 N/m.   a.24 mm b.27.4 mm c.20.6 mm d.3.4 mm

3) If two forces of 10,000 N are continuously rotating 1,000,000 shafts, the ball bearings and shaft thickness must be selected. The system should be drawn in 3D and proven to work safely. Please note that you must determine the dimensions of the system and the shaft material and code yourself. This question should only be answered if you are between 61 and 90 in the student list (#61-90). F Bearing ☑ ☑ ☑ ☑ Shaft F