heart valve assignment

What is the required diameter in meters of a cylindrical tank which has a length of 3 meters used for oil storage that will supply the engine for 5 days having a fuel consumption of 60Kg/hour at 27 degrees API? Please Answer # 9. If you can answer # 10 it will be appreciated much and rated high. Thanks!

Can I get some help looking over some sheets? I have most filled out, but just to double check for correctness and help with missing answers. Thank you

If one-third of the air in a tank is removed by each stroke of an air pump, what is the fractional part of the total air is removed in 6 strokes?Group of answer choices 525/765 335/765 665/729 786/766

What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing Adsorption Oxygen Generator (PSA) COMPs = Compressors POMPs = Pumps HEAT = Heat Exchanger PV = Flow Valves ST TANK = Storage Tank VENT = Vent DR = Drains PSV = Pressure Relief Valve In addition, what would be the possible problems that would require flexibility correction by adding expansion joints, spring supports, anchors and brackets?

MULTIPLE CHOICE -The answer is one of the options below please solve carefully and circle the correct option Please write clear .

Do not use Ai to answer this question.

I need problems 4, 5, and 6 answered.

1. In the operation of an internal combustion engine, the combustion gases expand in volume to make thepiston move. As this occurs ___________ gas particles move in the same direction as the motion of thepiston. Select the most correct phrase to go into this blank from these choices: A all theB almost all of theC very few of theD about half of the 3. What does the Second Law of Thermodynamics say about how much work can be done by a heat engine?Answer this in terms of either the heat added to the engine (Qh) or the heat expelled by the engine (Qc).

Please help, should correct. (Ai generated wrong ans not allowed)

A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4 CFM when operating. What is the minimum required CFM from a compressor which produces 120 psi?

I need these 3 parts answered. In manufacturing, dimensions often may fall in a range. For example, for three-place decimals, the values can fluctuate ±.010". What name is given to the area of the title block that includes this information? A. Tolerance Block B. Sizes Block C. Fluctuation Area D. Geometrics Zone   Which of the following is least likely to be found on a basic parts list?   A. Find Number B. Quantity Required C. Part Nomenclature D. Finish   American threads are specified by the number of threads per inch. If there are 12 threads per inch, then the pitch is ____.   A.   .083 B.   .100 C.   .125 D.   .187

Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle   Assuming the displacements of the cylinders are: Cyl. A DE = 65 in3 Cyl. A DR = 62 in3 Cyl. B DE = 44 in3 Cyl. B DR = 41 in3

Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and there is a dwell between some actions. What is the minimum flow rate required (CFM) to operate this cylinders? (enter answer with 2 decimal places) Sequence of operations: Cyl. A extends with metering (takes 1.5 second) Dwell time for 2 seconds for part machining Cyl. B extend and retracts without metering (2 second) Dwell time for 10 seconds while an electric mixer is operated Cyl. A retracts quicky with no metering (0.5 seconds) Dwell time for 5 seconds while a part is placed before next cycle Assuming the displacements of the cylinders are: Cyl. A DE 65 in³ = Cyl. A DR = 62 in³ = Cyl. B DE 44 in³ Cyl. B DR=41 in³

An exponent, such as the 4 in the expression 94, means: the number of times the number before the exponent is multiplied by itself (9 x 9 x 9x 9). O the number of times the number before the exponent is multiplied by 10 (9 x 10 x 10x 10 x 10). O the number to multiply the first number by (9 x 4). O the number of times the digit is written (9999). the number lo add to the first number (9 +4).

I need the answer for number 10.

Use the following information to answer the next three questions Mobile power plants, such as the one illustrated below, are used in remote locations. Flowing water turns a turbine, which then moves a coil of wire through a magnetic field. Mobile Power Plant Moving water Stream flowing downhill Location I Water turning turbine Location II -Spinning turbine -Permanent magnet Rotating wire coil Split-ring commutator Metal brush 10. The components that connect to the spinning turbine in the illustration on the previous page form a O ammeter O generator O motor 1. O transformer Your reasoning: MacBook Pro

Please show complete solutions and detailed drawings. Show conversions, units, and box in the final answers

I am sorry but your values when plugging in are not the correct values. Not too sure where your values are from but can you please redo the question using the given values in this problem and not from a different problem please? (example, height is not 29, it is 22) all values do not correlate to this problem. I was also told when finding the area of triangle to use (1/2)*b*h*Ad^2 and not 1/36*b*h*Ad^2     Find the moment of inertia and radius of gyration of the section of this bar about an axis parallel to x-axis going through the center of gravity of the bar. The bar is symmetrical about the axis parallel to y-axis and going through the center of gravity of the bar and about the axis parallel to z-axis and going through the center of gravity of the bar. The dimensions of the section are: l=55 mm, h=22 mm The triangle: hT=12 mm, lT=19 mm and the 2 circles: diameter=8 mm, hC=6 mm, dC=8 mm. A is the origin of the referential axis. Provide an organized table and explain all your steps…