Unit 11 Machining Specifications and Drawing Notes 229 - 2X .500 V.375 1. 2. D.250 V1.000 VØ.375 X 82' ubt 3. 4. Ø.750 THRU U01.250 V.375 SR.562 10 5. 6. .250 X 45 2X Ø.750 V1.500 LI01.000 V.250 L01.250 V.125 8 7. 4X .562 THRU SFIØ.625 .250 10. 9. 5X Ø.500, EQUALLY SPACED D.500 THRU 90 V.125 Copyright Goodheart-Willcox Co., Inc. IT VIVCH Print Reading for Industry 228 Class Date Name Review Activity 11-2 For each local note or callout given on the next page, use lettering to put the notes into words that example has been done for you. Also refer to Figure 11-5 as needed. can read. An you 1. Two .500" diameter holes, .375" deep. 2. 3. 4. 5. 6. 7. 8A 9- 10. nheart-Willcox Co, In

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: why is the angle 26.56 and then you use 22.56

A:

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: 4. How many datums are shown on the print? 5. What three symbols are used to describe the small…

A: What there's symbols are used to describe the small hole

Q: Draw the Mohr stress circles for the states of stress at a point given in the figures below. For (a)…

A: Draw the Mohr stress circles for the states of stress at a point given in the figures below.  To…

Q: How do you solve parts a,b and c?

A:

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: idk where you got the 4 from

A: The number of independent equations=5The number of unknowns=7To determine:Degree of freedom

Q: what is the omega value? as per the professor, the IC is at b not a

A: Given: The velocity of the upper wire: →V=5.6 m/s It is right that the instantaneous center of…

Q: N

A: Given: To find: Correct rotation code

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.