HI255_Unit_7_assignment_worksheet_2303B (1)

I need help solving problems 7, 8, and 9 pertaining to the print provided.

You are assigned as the head of the engineering team to work on selecting the right-sized blower that will go on your new line of hybrid vehicles.The fan circulates the warm air on the inside of the windshield to stop condensation of water vapor and allow for maximum visibility during wintertime (see images). You have been provided with some info. and are asked to pick from the bottom table, the right model number(s) that will satisfy the requirement. Your car is equipped with a fan blower setting that allow you to choose between speeds 0, 1,2 and 3. Variation of the convection heat transfer coefficient is dependent upon multiple factors, including the size and the blower configuration.You can only use the following parameters:

I need help solving problems 7, 8, and 9 pertaining to the print attached below.

Can you write me a program manuscript using geometric definition on FAPT language. The starting point is P1 and starts where the blue dot is. P1 = 0,0

I need help answering questions 7, 8, and 9 pertaining to the print attached.

Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors

Could you please fix my code it’s supposed to look like the graph that’s on the picture. But the lines do not cross eachother at the beginning. Could you make the lines look like the lines on the graph? Use this code in MATLAB and fix it. % Sample data for Diesel and Petrol cars carPosition = linspace(1, 60, 50); % Assumed positions of cars % Define your seed here seed = 50; rand('seed',seed); % Set the seed for reproducibility % Assumed CO2 emissions for Diesel and Petrol CO2Diesel = 25 + 5*cos(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Diesel CO2Petrol = 20 + 5*sin(carPosition/60*2*pi) + randn(1, 50)*5; % Random data for Petrol % Fit polynomial curves with a reduced degree of 2 pDiesel = polyfit(carPosition, CO2Diesel, 2); pPetrol = polyfit(carPosition, CO2Petrol, 2); % Generate points for best fit lines fitDiesel = polyval(pDiesel, carPosition); fitPetrol = polyval(pPetrol, carPosition); % Plotting the data figure; hold on; % Plot Diesel best fit line…

I need help solving this problem.

Use MATLAB please make code for this.

Do not give answer in image and hand writing

Question 4 List the steps in details to draw the shape below using AutoCAD commands 190 220 50 -90 - 50 114 81 R80 450 122 -R125 68 65 290 50 290 630

Can you help me with this problem? P1 is where the blue dot is

I am sorry but your values when plugging in are not the correct values. Not too sure where your values are from but can you please redo the question using the given values in this problem and not from a different problem please? (example, height is not 29, it is 22) all values do not correlate to this problem. I was also told when finding the area of triangle to use (1/2)*b*h*Ad^2 and not 1/36*b*h*Ad^2     Find the moment of inertia and radius of gyration of the section of this bar about an axis parallel to x-axis going through the center of gravity of the bar. The bar is symmetrical about the axis parallel to y-axis and going through the center of gravity of the bar and about the axis parallel to z-axis and going through the center of gravity of the bar. The dimensions of the section are: l=55 mm, h=22 mm The triangle: hT=12 mm, lT=19 mm and the 2 circles: diameter=8 mm, hC=6 mm, dC=8 mm. A is the origin of the referential axis. Provide an organized table and explain all your steps…

11)

Matlab Code

I need help with problems 1, 2, and 3 pertaining to the print provided below.