Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors

Q: ·50 70- 1.80 .60 .60 .8 .40 4.00 1.00 1.00 1.80 ANGLE STOP .50 40 1.60 .50 2.20 .50 1.20 .60 .80…

A: Draw the top, front and the right side view of the given figure.

Q: Assume that a security model is needed to protect information used in the class you aretaking—say,…

A: 27 cells are as follows: Confidentiality-Policy-Storage. Confidentiality-Policy-Processing.…

Q: fx A C 1 Variable Value Units 2 diameter 3 m 3 height 5 m 4 volume m^3 3 The image above shows a…

A:

Q: Consider a production process that produces batteries. A quality engineer has taken 28 samples each…

A:

Q: A dealer of white goods buys washing machines from Arçelik. In their next order, they plan to buy…

A: a) Machine 1: (of total 9250TL)Machine 2 :(of total 7483TL)b) Of maximum 23000TL :

Q: (ii) Figure A2-3 shows the torque and power of the employed EMRAX 208 Permanent magnet synchronous…

A: Given: To find: Design the drivetrain system

Q: The last 3 compartments in a feature control frame provides the datum references; this is known as…

A: The last 3 feature control frame provides the datum referances, this is known as datum order of…

Q: 1. A pressure gauge attached to a pipe is reading 1.34 m of Hg at a place where the atmospheric…

A: a) Pgau=1.35 m of Hg Patm=10.33 m of H2O…

Q: Gate AB in Figure below is 1.0 m long and 0.9 wide. Calculate force F on the gate and position X of…

A:

Q: Calculate the minimum and maximum values for the indicated dimensions attached. All minimum and…

A: Given: All the dimensions are shown below:

Q: Don't use chatgpt will upvote

A: The voltmeter reading in the given circuit is relatively independent of the temperature of the…

Q: I need help answering questions 4, 5, and 6 pertaining to the print provided below.

A: 4.Coordinate dimension location have boxes around them because it is representation standard of…

Q: 1. Based on the principles of sensor, design an inductive-type pressure sensor (input: pressure,…

A:

Q: A thermocouple (0-300°C) is used to measure temperature in a slow-moving gas. If you ed to choose an…

A:

Q: I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment.

A: The print sheet is showing the 3D view or perspective of the lower support cylinder union part.

Q: 2. Because parts washers use cleaning solutions that eventually become spent, they must be disposed…

A: Part washers are generally used to clean the  parts or components. part washers create hazardous…

Q: Questions 5 through 8 refer to the situation depicted below. Power la delivered by a motor (not…

A: The tight side or slag side of  of the pulley is  dependent on the  direction of the of the power…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: Here,in breadboard every horizontal lines like f1,g1,hq,i1,j1 are horizontally connected with each…

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.