EHR100 Week 1 Quiz

Truncation errors are increased as the round-off errors are decreased.Group of answer choices True False Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 29oC, 29.2oC, 29.3oC, 28.9oC, and 29.1oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is not accurate and not precise The thermometer is faulty. The thermometer is accurate and precise The thermometer is not accurate but precise. Say, you have a thermometer and you are checking the temperature of a body that has a temperature of 36o Using your thermometer five times, it gives you the following measurements: 36oC, 35.6oC, 36oC, 37oC, and 36.2oC. What can we conclude about the accuracy and the precision of the thermometer?Group of answer choices The thermometer is accurate and precise. The thermometer is accurate but not precise. The…

I need answers to questions 10, 11, and 12 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

Subject: Air Pollution Formation and Control Do not just copy and paster other online answers

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.

A new electronic component for aircraft is tested to withstand temperatures as low as -50°F. One engineer suggests that the device cannot actually stand temperatures that low. What are the Type I and Type II errors? Type I: The device CAN NOT withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN.Type II: The device CAN withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN NOT.   Type I: The device CAN withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN NOT.Type II: The device CAN NOT withstand temperatures as low as -50F but the engineer incorrectly finds that it CAN.    Is the answer the first or second bullet point?

please read everything properly... Take 3 4 5 hrs but solve full accurate drawing on bond paper don't use chat gpt etc okk

7

Question 2 You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the…

Please answer the 4th question

Please give a complete solution in Handwritten format. Strictly don't use chatgpt,I need correct answer. Engineering dynamics

Can someone please help me to answer all of the following questions thank you!!

! Required information 12 An asset owned by Photon Environmental was book depreciated by the Straight Line method over a 4-year period with book values of $296,000 and $243,000 in years 2 and 3, respectively. Determine the salvage value Sused in the calculation. The salvage value is determined to be $ es

Please give me the answers for this i been looking at this for a hour and my head hurts

I need these 3 parts answered for a review activity.

Question 2 In a test measuring the life span of a certain brand of tire, 100 tires are tested. The results showed an average lifetime of 50,000 miles, with a standard deviation of 5,000 miles. One hundred thousand of these tires have been sold and are on the road. (a) After what mileage would you expect 10% of the tires to have worn out? (b) How many tires are expected to wear out between 60,000 and 70,000 miles? (c) How many tires are expected to have a life of less than 20,000 miles? (d) What are your major assumptions in the calculations for (a), (b) and (c)? (e) Estimate the 95% confidence interval on the population mean.

Please assist with answering the following question?

I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for another tutor, thank you.

Select atleast two testing devices from among the categories (you may go beyond two). Discuss its application and methods of use. a. testing for speed (Tachometer), b. Testing of Air Consumption (Air-box method/viscous-flow meter), c. testing of exhaust smoke (Bosch/Hartridge/PHS), d. testing of exhaust emission (flame ionization detector/spectroscopic analyzers/gas chromatography) e. testing of torque (absorption dynamometer/transmission dynamometer).

I can't find the symbols for the blank ones