(a) Explanation The Figure-(1) shows the process of dual cycle on the P - v diagram. Figure-(1) Write the expression for the first law of thermodynamics for the heat addition process from state 2 to state 3. q 23 = ( u 3 − u 2 ) + w 23 (I) Here, the heat addition from the process 2-3 is q 23 , the internal energy at point 3 is u 3 , the internal energy at point 2 is u 2 and the work addition from 2-3 is W 23 . Since the work done from process 2-3 is zero so, w 23 = 0 Substitute 0 for W 23 , 1400 kJ / kg for q 23 in Equation (I). q 23 = m ( u 3 − u 2 ) (II) Write the formula of interpolation method of two variables. y 2 = ( x 2 − x 1 ) ( y 3 − y 1 ) ( x 3 − x 1 ) + y 1 (III) Here, the variables denote by x and y are specific internal energy and specific enthalpy at given condition. Formula for the isentropic compression is, V r 2 = 1 r V r 1 (IV) Here, the compression ratio is r and the relative volume at state 2 is V r 2 . Write the expression for the heat added in the process 2-3. q 23 = 2 3 q (V) Here, the total heat added is q and the heat added in the process 2-3 is q 23 . Write the expression for the heat addition process from 3-4. q 34 = h 4 − h 3 (VI) Here, the heat added is q 34 . Calculate the heat added in the process 3-4. q 34 = 1 3 q (VII) Write the expression for the isentropic expansion at state 4-5. V r 5 = r × T 3 T 4 × V r 4 (VIII) Conclusion: Refer to Table A-22 “Ideal Gas Properties of Air” to obtain the specific internal energy at temperature 300 K as, u 1 = 214.07 kJ / kg Here, the specific internal energy at state 1 is u 1 . Refer to Table A-22 “Ideal Gas Properties of Air” to obtain the critical volume at temperature 300 K as, V r 1 = 621.2 Here, the critical volume is V r 1 Substitute the given values in the Equation (III). V r 2 = 1 9 ( 621.2 ) = 69.02 Refer to Table A-22 “Ideal Gas Properties of Air” to obtain the specific internal energy at critical volume 69.02 as, u 2 = 514.49 kJ / kg Refer to Table A-22 “Ideal Gas Properties of Air” to obtain the temperature at critical volume 69.02 as, T 2 = 720.7 K Substitute 1400 kJ / kg for q in Equation (IV). q 2 − 3 = 2 3 ( 1400 kJ / kg ) = 933.33 kJ / kg Substitute 933.33 kJ / kg for Q 23 and 514.49 kJ / kg for u 2 in Equation (II). 933.33 kJ / kg = ( u 3 − 514.49 kJ / kg ) u 3 = 933.33 kJ / kg + 514.49 kJ / kg u 3 = 1447.82 kJ / kg Refer to the Table A22 “Ideal Gas Properties of Air” to obtain the Temperature at specific enthalpy 1447.82 kJ / kg as, T 3 = 1758.5 K Thus, the temperature at state 3 is 1758.5 K . Write the formula of interpolation method of two variables. y 2 = ( x 2 − x 1 ) ( y 3 − y 1 ) ( x 3 − x 1 ) + y 1 (IX) Here, the variables denote by x and y are specific internal energy and specific enthalpy at given condition. Show the specific internal energy in Table (1). Specific internal energy, ( kJ / kg ) Specific Enthalpy ( kJ / kg ) 1439.8 1941.6 1447.82 ? 1487.2 2003.3 Calculate the specific enthalpy at the given condition. Substitute 1439.8 kJ / kg for x 1 , 1447.82 kJ / kg for x 2 , 1487.2 kJ / kg for x 3 , 1941.6 kJ / kg for y 1 , and 2003.3 kJ / kg for y 3 in Equation (IX). y 2 = ( 1447.82 kJ / kg − 1439.8 kJ / kg ) ( 2003.3 kJ / kg − 1941.6 kJ / kg ) ( 1487.2 kJ / kg − 1439.8 kJ / kg ) + 1941.6 kJ / kg = 10.44 kJ / kg + 1941.6 kJ / kg = 1952.04 kJ / kg Write the specific enthalpy at state 3. h 3 = 1952 (b) To determine The work done by the cycle per unit mass of the air. (c) To determine The thermal efficiency. (d) To determine The mean effective pressure.

8th Edition

ISBN: 9781119391630

Author: MORAN

Publisher: WILEY

See similar textbooks

Question

Chapter 9.14, Problem 34P

(a)

To determine

The temperature at the end of each heat addition process.

(b)

To determine

The work done by the cycle per unit mass of the air.

(c)

To determine

The thermal efficiency.

(d)

To determine

The mean effective pressure.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.14, Problem 30P

Chapter 9.14, Problem 35P

Students have asked these similar questions

Q6] (20 Marks) Select the most suitable choice for the following statements: modo digi -1A 10 af5 1 -The copper-based alloy which is responded to age hardening is a) copper-nickel b) aluminum bronze c) copper - beryllium d) brass besincaluy 2- Highly elastic polymers may experience elongations to greater than.... b) 500% bromsia-P c) 1000%. d) 1200% 15m or -2 a)100% 3- The cooling rate of quenching the steel in saltwater will be ......the cooling rate of quenching ir c) faster than sold) none of them a) slower than 4- Adding of a) Cr b) the same as ...... Will lead to stabilize the b) Mo 10 austenite in steel. c) Nimble avolls 1d) Sized loloin nl 5- The adjacent linear chains of crosslinked polymers are joined one to another at various positic DIR... by.........bonds c) covalent noisqo gd) ionic lg 120M 6- For the ceramic with coordination number 6 the cation to anion radius ratio will be a) Van der Waals a) 0.155-0.225 a) linear b) hydrogen (b) 0.225-0.414 c) 0.414 0.732 ..polymers.…

Examine Notes: Attempt Six Questions Only. rever necessa , Q1] (20 Marks) Answer with true (T) or false (F), corrects the wrong phrases, and gives sho reasons for correct and corrected statements: 1- High chromium irons are basically grey cast irons alloyed with 12 to 30 % Cr. yous board-19qgo orT-1 2- The drawbacks of Al- Li alloys are their high young modulus and high density.&M 0) (0 3- Vulcanized rubbers are classified under thermoplastic polymers. 4- Diamond is a stable carbon polymorph at room temperature and atmospheric pressure. ( 5- The metallic ions of ceramic are called anions, and they are positively charged. yldgiH-S 69001(6

H.W 5.4 Calculate the load that will make point A move to the left by 6mm, E-228GPa. The diameters of the rods are as shown in fig. below. 2P- PA 50mm B 200mm 2P 0.9m 1.3m

Chapter 9 Solutions

FUND OF ENGINEERING THERMO W/WILEY PLU

Ch. 9.14 - Prob. 1E Ch. 9.14 - Prob. 2E Ch. 9.14 - Prob. 3E Ch. 9.14 - Prob. 4E Ch. 9.14 - Prob. 5E Ch. 9.14 - 6. What is the purpose of a rear diffuser on a...Ch. 9.14 - 7. What is the meaning of the octane rating that...Ch. 9.14 - Prob. 8E Ch. 9.14 - Prob. 9E Ch. 9.14 - 10. What is the purpose of the gas turbine–powered...

Knowledge Booster