(a) Explanation The figure below shows the T - s diagram of the ideal air-standard regenerative cycle. Figure-(1) The process 1-2 is an isentropic expansion process, 2-3 is an isobaric heat addition process, 3-4 is an isentropic compression process and 4-1 is an isobaric heat rejection process. The regeneration takes place in 2- x . Write the expression for the temperature at state 2. T 2 = T 1 ( p 2 p 1 ) k − 1 k (I) Here, the pressure at state 2 is p 2 , the pressure at state 1 is p 1 , the temperature at state 1 is T 1 and the adiabatic constant is k . Write the expression for the temperature at state 4. T 4 = T 3 ( p 4 p 3 ) k − 1 k (II) Here, the pressure at state 4 is p 4 , the pressure at state 3 is p 3 and the temperature at state 3 is T 3 . Write the expression for the net turbine work. W ˙ n e t = m ˙ [ ( h 3 − h 4 ) − ( h 2 − h 1 ) ] (III) Here, the specific enthalpy at state 1 is h 1 , the specific enthalpy at state 2 is h 2 , the specific enthalpy at state 3 is h 3 , the specific enthalpy at state 4 is h 4 and the mass flow rate is m ˙ . Write the expression for the specific enthalpy change in process 1-2. h 2 − h 1 = c p ( T 2 − T 1 ) Write the expression for the specific enthalpy change in process 3-4. h 3 − h 4 = c p ( T 3 − T 4 ) Substitute c p ( T 3 − T 4 ) for h 3 − h 4 and c p ( T 2 − T 1 ) for h 2 − h 1 in the Equation (III). W ˙ n e t = m ˙ [ c p ( T 3 − T 4 ) − c p ( T 2 − T 1 ) ] = m ˙ c p [ T 3 − T 4 − T 2 + T 1 ] W ˙ n e t m ˙ = c p [ T 3 − T 4 − T 2 + T 1 ] (IV) (b) To determine The energy added by heat transfer. (c) To determine The thermal efficiency. (d) To determine The thermal efficiency by using Equation 9.65.

8th Edition

ISBN: 9781119391630

Author: MORAN

Publisher: WILEY

See similar textbooks

Videos

Question

Chapter 9.14, Problem 66P

(a)

To determine

The net work developed in the cycle.

(b)

To determine

The energy added by heat transfer.

(c)

To determine

The thermal efficiency.

(d)

To determine

The thermal efficiency by using Equation 9.65.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 9.14, Problem 65P

Chapter 9.14, Problem 67P

Students have asked these similar questions

H.W 5.4 Calculate the load that will make point A move to the left by 6mm, E-228GPa. The diameters of the rods are as shown in fig. below. 2P- PA 50mm B 200mm 2P 0.9m 1.3m

d₁ = = Two solid cylindrical road AB and BC are welded together at B and loaded as shown. Knowing that 30mm (for AB) and d₂ 50mm (for BC), find the average normal stress in each road and the total deformation of road AB and BC. E=220GPa H.W 5.3 60kN A For the previous example calculate the value of force P so that the point A will not move, and what is the total length of road AB at that force? P◄ A 125kN 125kN 0.9m 125kN 125kN 0.9m B B 1.3m 1.3m

Class: B Calculate the load that will make point A move to the left by 6mm, E-228GPa The cross sections of the rods are as shown in fig. below. 183 P- Solution 1.418mm 200mm 80mm 3P- 18.3 A 080mm B 200mm 3P- 0.9m إعدادات العرض 1.3m 4.061mm

Chapter 9 Solutions

FUND OF ENGINEERING THERMO W/WILEY PLU

Ch. 9.14 - Prob. 1E Ch. 9.14 - Prob. 2E Ch. 9.14 - Prob. 3E Ch. 9.14 - Prob. 4E Ch. 9.14 - Prob. 5E Ch. 9.14 - 6. What is the purpose of a rear diffuser on a...Ch. 9.14 - 7. What is the meaning of the octane rating that...Ch. 9.14 - Prob. 8E Ch. 9.14 - Prob. 9E Ch. 9.14 - 10. What is the purpose of the gas turbine–powered...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.