Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 9, Problem 9.71P
Hot air flows from a furnace through a 0.15-m-diameter, thin-walled steel duct with a velocity of 3 m/s. The duct passes through the crawlspace of a house, and its uninsulated exterior surface is exposed to quiescent air and surroundings at 0°C.
(a) At a location in the duct for which the mean air temperature is 70°C, determine the heat loss per unit duct length and the duct wall temperature. The duct outer surface has an emissivity of 0.5.
(b) If the duct is wrapped with a 25-mm-thick layer of 85% magnesia insulation
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Thermal energy generated by the electrical resistance of a 5-mm-diameter and 4-m- long bare cable is dissipated to the surrounding air at 80°C. The voltage drop and the electric current across the cable in steady operation are measured to be 18 V and 5 A, respectively. Disregarding radiation, estimate the surface temperature of the cable. Evaluate air properties at a film temperature of 100°C and 1 atm pressure.
Determine the convection heat transfer coefficient for the flow of
(a) fluid A and
(b) fluid B
at a velocity of 2 m/s in a 10-cm diameter and 10-m long tube when the tube is subjected to uniform heat flux from all surfaces. Use fluid properties at 25°C.
Fins, or extended surfaces, commonly are used in a variety of engineering applications to enhance cooling. Common examples include a motorcycle engine head, a lawn mower engine head, extended surfaces used in electronic equipment, and finned tube heat exchangers in room heating and cooling applications. Consider aluminum fins of a rectangular profile, which are used to remove heat from a surface whose temperature is100° C . The temperature of the ambient air is 20° C. We are interested in determining how the temperature of the fin varies along its length and plotting this temperature variation. For long fins, the temperaturedistribution along the fin is given by
Chapter 9 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 9 - The one-dimensional plane wall of Figure 3.1 is of...Ch. 9 - Using the values of density for water in Table...Ch. 9 - Consider an object of Characteristic length 0.01 m...Ch. 9 - To assess the efficacy of different liquids for...Ch. 9 - In many cases, we are concerned with free...Ch. 9 - The heat transfer rate due to free convection from...Ch. 9 - Consider a large vertical plate with a uniform...Ch. 9 - For laminar free convection flow on a vertical...Ch. 9 - Consider an array of vertical rectangular tins,...Ch. 9 - A number of thin plates are to be cooled by...
Ch. 9 - Prob. 9.11PCh. 9 - Prob. 9.13PCh. 9 - The plate described in Problem 9.14 has been used...Ch. 9 - Determine the average convection heat transfer...Ch. 9 - Consider a vertical plate of dimension 0.025m0.50m...Ch. 9 - During a winter day, the window of a patio door...Ch. 9 - Prob. 9.20PCh. 9 - A household oven door of 0.5-m height and 0.7-m...Ch. 9 - Consider a vertical, single-pane window of...Ch. 9 - Consider laminar flow about a vertical isothermal...Ch. 9 - Consider the conveyor system described in Problem...Ch. 9 - Prob. 9.25PCh. 9 - Consider an experiment to investigate the...Ch. 9 - The vertical rear window of an automobile is of...Ch. 9 - Prob. 9.28PCh. 9 - Prob. 9.29PCh. 9 - Prob. 9.30PCh. 9 - A refrigerator door has a height and width of...Ch. 9 - In the central receiver concept of a solar power...Ch. 9 - Prob. 9.34PCh. 9 - Airflow through a long, 0.2-m-square air...Ch. 9 - Prob. 9.36PCh. 9 - An electrical heater in the form of a horizontal...Ch. 9 - Consider a horizontal 6-mm-thick, 100-mm-long...Ch. 9 - Prob. 9.39PCh. 9 - Prob. 9.40PCh. 9 - Prob. 9.41PCh. 9 - Many laptop computers are equipped with thermal...Ch. 9 - Prob. 9.43PCh. 9 - At the end of its manufacturing process, a silicon...Ch. 9 - Integrated circuit (IC) boards are stacked within...Ch. 9 - Prob. 9.48PCh. 9 - Prob. 9.50PCh. 9 - Prob. 9.51PCh. 9 - Prob. 9.52PCh. 9 - Prob. 9.53PCh. 9 - Prob. 9.54PCh. 9 - Prob. 9.55PCh. 9 - Prob. 9.56PCh. 9 - Prob. 9.57PCh. 9 - A horizontal tube of 12.5-mm diameter with an...Ch. 9 - Prob. 9.60PCh. 9 - Prob. 9.61PCh. 9 - Prob. 9.63PCh. 9 - Prob. 9.64PCh. 9 - Common practice in chemical processing plants is...Ch. 9 - Consider the electrical heater of Problem 7.49. If...Ch. 9 - Prob. 9.67PCh. 9 - A billet of stainless steel, AISI 316, with a...Ch. 9 - Lone stainless steel rods of 50-mm diameter are...Ch. 9 - Hot air flows from a furnace through a...Ch. 9 - A biological fluid moves at a flow rate of...Ch. 9 - A sphere of 25-mm diameter contains an embedded...Ch. 9 - Prob. 9.79PCh. 9 - A vertical array of circuit boards is immersed in...Ch. 9 - Prob. 9.81PCh. 9 - The front door of a dishwasher of width 580 mm has...Ch. 9 - A natural convection air healer consists of an...Ch. 9 - A bank of drying ovens is mounted on a rack in a...Ch. 9 - Prob. 9.85PCh. 9 - Prob. 9.86PCh. 9 - Prob. 9.87PCh. 9 - To reduce heat losses, a horizontal rectangular...Ch. 9 - Prob. 9.89PCh. 9 - Prob. 9.90PCh. 9 - Prob. 9.91PCh. 9 - Prob. 9.92PCh. 9 - A 50-mm-thick air gap separates two horizontal...Ch. 9 - Prob. 9.94PCh. 9 - A vertical, double-pane window, which is 1 m on a...Ch. 9 - The top surface (0.5m0.5m) of an oven is 60°C for...Ch. 9 - Prob. 9.97PCh. 9 - Prob. 9.98PCh. 9 - Consider the cylindrical. 0.12-m-diamter radiation...Ch. 9 - Prob. 9.100PCh. 9 - A solar collector design consists of an inner tube...Ch. 9 - Prob. 9.104PCh. 9 - Prob. 9.105PCh. 9 - Liquid nitrogen is stored in a thin-walled...Ch. 9 - Prob. 9.108PCh. 9 - Prob. 9.109PCh. 9 - Prob. 9.110PCh. 9 - Prob. 9.111PCh. 9 - Prob. 9.114PCh. 9 - Prob. 9.115PCh. 9 - Prob. 9.116PCh. 9 - Prob. 9.117PCh. 9 - A water bath is used to maintain canisters...Ch. 9 - On a very Still morning, the surface temperature...Ch. 9 - Fuel cells similar to the PEM cell of Example 1.5...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Define or describe each type of fluid: (a) viscoelastic fluid (b) pseudoplastic fluid (c) dilatant fluid (d) Bi...
Fluid Mechanics: Fundamentals and Applications
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
List several uses of the arbor press.
Machine Tool Practices (10th Edition)
5.1 through 5.9
Locate the centroid of the plane area shown.
Fig. P5.1
Vector Mechanics for Engineers: Statics and Dynamics
Select a mechanical component from Part 3 of this book (roller bearings, springs, etc.), go to the Internet, an...
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
19.8 Calculate the allowable tensile load for the connection shown. The plates are ASTM A36 steel and the weld ...
Applied Statics and Strength of Materials (6th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Exhaust gases from a manufacturing plant are being discharged through a 10-m-tall exhaust stack with outer diameter of 1 m. The exhaust gases are discharged at a rate of 0.125 kg/s, while temperature drop between inlet and exit of the exhaust stack is 30°C, and the constant pressure-specific heat of the exhaust gases is 1600 J/kg.K. On a particular calm day, the surrounding quiescent air temperature is 33°C. Solar radiation is incident on the exhaust stack outer surface at a rate of 500 W/m2, and both the emissivity and solar absorptivity of the outer surface are 0.9. Determine the exhaust stack outer surface temperature. Assume the film temperature is 60°C.arrow_forwardA large bare duct having a diameter of 25cm runs horizontally across a factory area having environmental conditions of 20.C and 1 atm. The length of the duct is 100 m. Inside the duct a low pressure steam flow maintains the duct wall temperature constant at 120.C. Calculate the total heat lost by convection from the duct to the roomarrow_forwardA double window called thermopane is one in which two layers of glass are used separated by a layer o dry stagnant air: In a given window, each of the glass layers is 6.35 mm thick separated by a 6.35 mm space of stagnant air. The thermal conductivity of the glass is 0.869 W/m K and that of air is 0.026 over the temperature range used. For temperature drop of 27.8 K over the system, calculate the heat loss for a window 0.914 m 1.83 m.arrow_forward
- Please solve ASAParrow_forwardQuestion 12 [5 Mark] A 10-cm-wide and 15-cm-high vertical hot surface in 25 °C air is to be cooled by a heat sink with equally spaced fins of rectangular profile. The fins are 1 mm thick and 15 cm long in the vertical direction and have a height of 25 mm from the base. Draw the neat figure of the setup and determine the optimum fin spacing and the rate of heat transfer by convection from the heat sink if the base temperature is 90 °C.arrow_forwardThermodynamics problem. A membrane type electrical heater of 20,000 w/m? capacity is sandwiched between an Insulation of 25 mm thickness with thermal conductivity of 0.029 W/m-K and a metal plate with k = 12.6 W/m-K of thickness 15 mm. The convection coefficient is 150 W/m2-K. The surroundings are at 5°C. Determine the surface temperature of the heater and the flow on either side.arrow_forward
- 3. Consider a hot automotive engine, which can be approximated as a 0.6 m high, 0.3 m wide, and 0.9 m long rectangular block. The bottom surface of the block is at a temperature of 90°C and has an emissivity of 0.9. The ambient air is at 23°C, and the road surface is at 28°C. The fluid properties of air are determined at the film temperature and can be found in the tables at the end of the tutorial. a. Determine the rate of heat transfer from the bottom surface of the engine block by convection and radiation as the car travels at a velocity of 60 km/h. b. If the temperatures were measured with a thermometer accurate to the nearest 1°C, what in the resultant heat is the uncertainty transfer rate? (You may ignore the uncertainties when calculating your fluid properties). c. If the speedometer in the car is accurate to the nearest 2km/h, what is the uncertainty in the result?arrow_forwardRequired information Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a temperature of 24°C. The pipe's inner diameter is 4 cm, and its length is 4 m. The first half of the pipe is kept at a constant wall temperature of 100°C. The second half of the pipe is subjected to a constant heat flux of 200 W. The properties of air at 80°C are p = 0.9994 kg/m³, k = 0.02953 W/m-K, v= 2.097 x 10-5 m²/s, cp=1008 J/kg-K, and Pr = 0.7154. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air 1.25 m/s 2m T, = 100°C D = 4 cm 2 m g, = 200 W Determine the wall temperature at the exit of the tube. The wall temperature at the exit of the tube is 282 * °C.arrow_forwardHeat transferarrow_forward
- (A) Answer the following: (1) Explain the concept of convection heat transfer. What are the methods used for calculating the heat transfer coefficient. (2) Define the following: a. Drag coefficient b. fully developed flow. c. Reynolds number. (B) Explain the difference between forced and free convectionarrow_forwardWater at 340 K and a flow rate of 5 kg/s enters a black, thin-walled tube, which passes through a large furnace whose walls and air are at a temperature of 700 K. The diameter and length of the tube are 0.25 m and 8 m, respectively. Convection coefficients associated with water flow through the tube and airflow over the tube are 300 W/m²-K and 50 W/m².K, respectively. Water Tme= i m = 5 kg/s Tai K Tube, D = 0.25 m L = 8 m, ε = 1 Air T= 700 K -Furnace, Tur 700 K Write an expression for the linearized radiation coefficient corresponding to radiation exchange between the outer surface of the pipe and the furnace walls. Determine how to calculate this coefficient if the surface temperature of the tube is represented by the arithmetic mean of its inlet and outlet values. Use these expressions to determine the outlet temperature of the water, Tm,o, in K. Tmoarrow_forwardChips of width L _ 15 mm on a side are mounted to a substrate that is installed in an enclosurewhose walls and air are maintained at a temperature of Tsur=T∞=25oC. The chips have an emissivity ofε=0.60 and a maximum allowable temperature of Ts=85oC.(a) If heat is rejected from the chips by radiation and natural convection, what is the maximum operatingpower of each chip? The convection coefficient may be approximated as h=11.7 W/m2K.(b) If a fan is used to maintain airflow through the enclosure and heat transfer is by only forcedconvection, with h=250 W/m2K, what is the maximum operating power?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license