The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options. Concept introduction: Steps involving standard solution preparation: The steps involving in the preparation of known molar solution using volumetric flask are, The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark. Errors in standard solution preparation: Incorrect weight of solute makes a concentration change in final solution. Loss of solute particles results lower the concentration of final solution. Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases. Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Question

Want to see the full answer?

Answer 1

Question

Chapter 9, Problem 9.3VC

Interpretation Introduction

Interpretation:

The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options.

Concept introduction:

Steps involving standard solution preparation:

The steps involving in the preparation of known molar solution using volumetric flask are,

The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark.

Errors in standard solution preparation:

Incorrect weight of solute makes a concentration change in final solution.

Loss of solute particles results lower the concentration of final solution.

Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases.

Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Students have asked these similar questions

What are the retrosynthesis and forward synthesis of these reactions?

Which of the given reactions would form meso product? H₂O, H2SO4 III m CH3 CH₂ONa CH3OH || H₂O, H2SO4 CH3 1. LiAlH4, THF 2. H₂O CH3 IV

What is the major product of the following reaction? O IV III HCI D = III ა IV

Answer 2

Question

Chapter 9, Problem 9.3VC

Interpretation Introduction

Interpretation:

The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options.

Concept introduction:

Steps involving standard solution preparation:

The steps involving in the preparation of known molar solution using volumetric flask are,

The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark.

Errors in standard solution preparation:

Incorrect weight of solute makes a concentration change in final solution.

Loss of solute particles results lower the concentration of final solution.

Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases.

Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 3

Question

Chapter 9, Problem 9.3VC

Interpretation Introduction

Interpretation:

The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options.

Concept introduction:

Steps involving standard solution preparation:

The steps involving in the preparation of known molar solution using volumetric flask are,

The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark.

Errors in standard solution preparation:

Incorrect weight of solute makes a concentration change in final solution.

Loss of solute particles results lower the concentration of final solution.

Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases.

Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 4

Question

Chapter 9, Problem 9.3VC

Interpretation Introduction

Interpretation:

The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options.

Concept introduction:

Steps involving standard solution preparation:

The steps involving in the preparation of known molar solution using volumetric flask are,

The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark.

Errors in standard solution preparation:

Incorrect weight of solute makes a concentration change in final solution.

Loss of solute particles results lower the concentration of final solution.

Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases.

Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 5

Chapter 9, Problem 9.3VC

Interpretation Introduction

Interpretation:

The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options.

Concept introduction:

Steps involving standard solution preparation:

The steps involving in the preparation of known molar solution using volumetric flask are,

The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark.

Errors in standard solution preparation:

Incorrect weight of solute makes a concentration change in final solution.

Loss of solute particles results lower the concentration of final solution.

Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases.

Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Answer 6

Chapter 9, Problem 9.3VC

Interpretation Introduction

Interpretation:

The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options.

Concept introduction:

Steps involving standard solution preparation:

The steps involving in the preparation of known molar solution using volumetric flask are,

The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark.

Errors in standard solution preparation:

Incorrect weight of solute makes a concentration change in final solution.

Loss of solute particles results lower the concentration of final solution.

Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases.

Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Answer 7

Chapter 9, Problem 9.3VC

Interpretation Introduction

Interpretation:

The cause for prepared solution concentration is not to be exactly 0.1 M should be found from the given options.

Concept introduction:

Steps involving standard solution preparation:

The steps involving in the preparation of known molar solution using volumetric flask are,

The calculated mass of the solute is weighed in the balance and the weighed solute is transferred in to the volumetric flack. Then small quantity of water is added in to the volumetric flack and shaken to dissolve the solute. After dissolving solute particles, water is poured into the volumetric flack to reach the mark.

Errors in standard solution preparation:

Incorrect weight of solute makes a concentration change in final solution.

Loss of solute particles results lower the concentration of final solution.

Before the addition of solute, if water is filled in the volumetric flask to reach the mark, the resulting volume changes (increasing of volume) in final solution, this volume changes makes concentration decreases.

Neglecting addition of last bit of water into volumetric flask to reach the mark results in lower volume than the calculated volume.

Answer 8

Expert Solution & Answer

Answer 9

Expert Solution & Answer

Answer 10

Want to see the full answer?

Check out a sample textbook solution

See solution

Answer 11

Ch. 9.1 - Sports drinks typically contain sucrose...Ch. 9.1 - Prob. 1PPA Ch. 9.1 - Prob. 1PPB Ch. 9.1 - Prob. 1PPC Ch. 9.1 - Prob. 9.1.1SR Ch. 9.1 - Prob. 9.1.2SR Ch. 9.1 - Prob. 9.1.3SR Ch. 9.2 - Classify each of the following compounds as...Ch. 9.2 - Prob. 2PPA Ch. 9.2 - Prob. 2PPB

Solution Summary: The author explains that the cause for prepared solution concentration is not to be exactly 0.1M from the given options.

Videos

Want to see the full answer?

Chapter 9 Solutions