Bundle: Mechanics Of Materials, Loose-leaf Version, 9th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
9th Edition
ISBN: 9781337594318
Author: Barry J. Goodno; James M. Gere
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 8, Problem 8.5.16P
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The cross section of a concrete dam is shown in the figure. Take the weight-density (= pg)
of water to be 10 kN/m³ and that of concrete to be 25 kN/m³. For the given design of the
cross-section, find the ratio h/H that is safe enough for the dam to not tip over (about the
downstream edge E).
Here you will enter the numerical answer. In the handworked file you must show your worked
solution.
H
E
60°
H/10
4H/10
h
An aluminum pole for a street light weighs4600 N and supports an arm that weighs 660 N (seefigure). The center of gravity of the arm is 1.2 m from theaxis of the pole. A wind force of 300 N also acts in the (-y)direction at 9 m above the base. The outside diameter ofthe pole (at its base) is 225 mm, and its thickness is 18 mm.
Determine the maximum tensile and compressivestresses σt and σc, respectively, in the pole (at its base)due to the weights and the wind force.
A sign is supported by a pipe (see figure)having an outer diameter 110 mm and inner diameter90 mm. The dimensions of the sign are 2.0 m 3 1.0 m,and its lower edge is 3.0 m above the base. Note that thecenter of gravity of the sign is 1.05 m from the axis ofthe pipe. The wind pressure against the sign is 1.5 kPa.Determine the maximum in-plane shear stressesdue to the wind pressure on the sign at points A, B, andC, located on the outer surface at the base of the pipe.
Chapter 8 Solutions
Bundle: Mechanics Of Materials, Loose-leaf Version, 9th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
Ch. 8 - A spherical balloon is filled with a gas. The...Ch. 8 - A spherical balloon with an outer diameter of 500...Ch. 8 - A large spherical tank (see figure) contains gas...Ch. 8 - Solve the preceding problem if the internal...Ch. 8 - A hemispherical window (or viewport) in a...Ch. 8 - A rubber ball (sec figure) is inflated to a...Ch. 8 - (a) Solve part (a) of the preceding problem if the...Ch. 8 - A spherical steel pressure vessel (diameter 500...Ch. 8 - A spherical tank of diameter 48 in. and wall...Ch. 8 - Solve the preceding problem for the following...
Ch. 8 - A spherical stainless-steel tank having a diameter...Ch. 8 - Solve the preceding problem if the diameter is 480...Ch. 8 - : A hollow, pressurized sphere having a radius r =...Ch. 8 - A fire extinguisher tank is designed for an...Ch. 8 - Prob. 8.3.2PCh. 8 - A scuba t a n k (see fig ure) i s bci ng d e...Ch. 8 - A tall standpipc with an open top (see figure) has...Ch. 8 - An inflatable structure used by a traveling circus...Ch. 8 - A thin-walled cylindrical pressure vessel of a...Ch. 8 - A strain gage is installed in the longitudinal...Ch. 8 - A circular cylindrical steel tank (see figure)...Ch. 8 - A cylinder filled with oil is under pressure from...Ch. 8 - Solve the preceding problem if F =90 mm, F = 42...Ch. 8 - A standpipe in a water-supply system (see figure)...Ch. 8 - A cylindrical tank with hemispherical heads is...Ch. 8 - : A cylindrical tank with diameter d = 18 in, is...Ch. 8 - A pressurized steel tank is constructed with a...Ch. 8 - Solve the preceding problem for a welded Tank with...Ch. 8 - A wood beam with a cross section 4 x 6 in. is...Ch. 8 - Prob. 8.4.2PCh. 8 - A simply supported beam is subjected to two point...Ch. 8 - A cantilever beam with a width h = 100 mm and...Ch. 8 - A beam with a width h = 6 in. and depth h = 8 in....Ch. 8 - Beam ABC with an overhang BC is subjected to a...Ch. 8 - A cantilever beam(Z, = 6 ft) with a rectangular...Ch. 8 - Solve the preceding problem for the following...Ch. 8 - A simple beam with a rectangular cross section...Ch. 8 - An overhanging beam ABC has a guided support at A,...Ch. 8 - Solve the preceding problem if the stress and...Ch. 8 - A cantilever wood beam with a width b = 100 mm and...Ch. 8 - . A cantilever beam (width b = 3 in. and depth h =...Ch. 8 - A beam with a wide-flange cross section (see...Ch. 8 - A beam with a wide-flange cross section (see...Ch. 8 - A W 200 x 41.7 wide-flange beam (see Table F-l(b),...Ch. 8 - A W 12 x 35 steel beam is fixed at A. The beam has...Ch. 8 - A W 360 x 79 steel beam is fixed at A. The beam...Ch. 8 - A W 12 X 14 wide-flange beam (see Table F-l(a),...Ch. 8 - A cantilever beam with a T-section is loaded by an...Ch. 8 - Beam A BCD has a sliding support at A, roller...Ch. 8 - , Solve the preceding problem using the numerical...Ch. 8 - A W 12 x 35 steel cantilever beam is subjected to...Ch. 8 - A W 310 x 52 steel beam is subjected to a point...Ch. 8 - A solid circular bar is fixed at point A. The bar...Ch. 8 - A cantilever beam with a width h = 100 mm and...Ch. 8 - Solve the preceding problem using the following...Ch. 8 - A cylindrical tank subjected to internal...Ch. 8 - A cylindrical pressure vessel having a radius r =...Ch. 8 - A pressurized cylindrical tank with flat ends is...Ch. 8 - A cylindrical pressure vessel with flat ends is...Ch. 8 - The tensional pendulum shown in the figure...Ch. 8 - The hollow drill pipe for an oil well (sec figure)...Ch. 8 - Solve the preceding problem if the diameter is 480...Ch. 8 - . A segment of a generator shaft with a hollow...Ch. 8 - A post having a hollow, circular cross section...Ch. 8 - A sign is supported by a pole of hollow circular...Ch. 8 - A sign is supported by a pipe (see figure) having...Ch. 8 - A traffic light and signal pole is subjected to...Ch. 8 - Repeat the preceding problem but now find the...Ch. 8 - A bracket ABCD having a hollow circular cross...Ch. 8 - A gondola on a ski lift is supported by two bent...Ch. 8 - Beam A BCD has a sliding support at A, roller...Ch. 8 - A double-decker bicycle rack made up of square...Ch. 8 - A semicircular bar AB lying in a horizontal plane...Ch. 8 - Repeat Problem 8.5-22 but replace the square tube...Ch. 8 - An L-shaped bracket lying in a horizontal plane...Ch. 8 - A horizontal bracket ABC consists of two...Ch. 8 - , An arm A BC lying in a horizontal plane and...Ch. 8 - A crank arm consists of a solid segment of length...Ch. 8 - A moveable steel stand supports an automobile...Ch. 8 - A mountain bike rider going uphill applies a force...Ch. 8 - Determine the maximum tensile, compressive, and...Ch. 8 - Prob. 8.5.32PCh. 8 - A plumber's valve wrench is used to replace valves...Ch. 8 - A compound beam ABCD has a cable with force P...Ch. 8 - A steel hanger bracket ABCD has a solid, circular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.arrow_forwardThe pressure vessel has a thickness 2 cm, diameter 20 cm. Calculate the internal pressure longitudinally and laterally. If the longitudinal stress is limited to 150 MPa and the circumferential stress is limited to 100 MPa. Which one will be used for safety? *arrow_forwardThe masonry dam of trapezoidal section has its upstream face vertical. The height is 10 m and top is 3 m wide. Find the minimum width of base if there is no tension at the base and water reaches the top of the dam. Take weight of water= 9.81 kN/m³ and weight of masonry = 22 kN/ m³. What is then maximum compressive stress at the base? [Ans. b = 6 m, 330 kN/m2]arrow_forward
- How do I calculate for sigma seam? Thank youarrow_forwardThe axial and circumferential stress experienced by the cylinder wall at mid-depth (1m as shown)arrow_forwardA triangular dam is shown in the figure, base is 6-m and height is 8-m. Compute for the factor of safety against sliding and overturning. Unit weight of concrete is 23.54 kN/cu.m. Consider 1 meter length strip. Disregard hydrostatic uplift pressure. The coefficient between the dam and the foundation is 0.8. harrow_forward
- The inner diameter of the AB compressed air tank is 160, the wall thickness is 1.Since the manometer pressure in the tank is 1,6 ,at point a at the top of the tank maximum normal stress and determine the maximum plane shear stress.(c=16 , d=38, e =32, g=160, h=1, k =1.6 , F=160)arrow_forwardI can't seem to find the shear stress at point b. Here's my work for reference.arrow_forwardSolve itarrow_forward
- The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 165 mm from the centroid of the rivet group. Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPaarrow_forwardDimensions 2.0 x 1.2 m sign board, circular with outer diameter 220 mm and inner diameter 180 mmit is desired to be carried by cross-section mast 0.50 m outside the axis of the sign plate to the poleit is connected and its lower edge is 6,00 m above the ground. Wind where the plate is placedit is known that its pressure is no more than 2.0 kPa. A and B of the cross-section connecting my pole to the groundfind the largest normal and shear stresses that will occur at their points.arrow_forwardA cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. Find the longitudinal stress in the tank.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Pressure Vessels Introduction; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=Z1J97IpFc2k;License: Standard youtube license