Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
10th Edition
ISBN: 9780073398204
Author: Richard G Budynas, Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 8, Problem 30P
(a)
To determine
The maximum bolt preload which is possible to apply without exceeding the proof strength of the bolt.
(b)
To determine
The minimum bolt preload that can be applied without joint separation.
(c)
To determine
The value of torque that is specified for preloading the bolt to the midpoint of the values found in (a) and (b).
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
For a bolted assembly with six bolts, the stiffness of each bolt is kb = 2.8 Mlbf/in and the stiffness of the members is km=
14 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the
bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. Assume the bolts are preloaded to 75
percent of the proof load.
Determine the yielding factor of safety.
The yielding factor of safety is
For a bolted assembly with four bolts, the stiffness of each bolt is
kb = 3.0 MN/mm and the stiffness at the members is km = 4.2
MN/mm per bolt. The bolts are pre-loaded to 75% of the proof
strength.
Assume the external load is equally distributed to all the bolts.
The bolts are M16x1.5 class 8.8 with rolled threads. A fluctuating
external load is applied to the entire joint with Pmax = 160 kN and
Pmin = 80 kN.
Determine the factor of safety against fatigue failure using the
Goodman criterion.
For a bolted assembly with 8 bolts, the stiffness of
each bolt is k_b = 1.1 N/mm and the stiffness of the
members is k_m = 2.8 N/mm at each bolt location. The
joint is subject to occasional disassembly for
maintenance and should be preloaded accordingly (to
75% of the proof stress). Assume the external load is
equally distributed to all the bolts. It has been
determined to use M6 × 1 class 5.8 bolts with rolled
threads.
Determine the maximum safe working load that both
limits the stress in the bolts to be below the proof
stress and ensures that the members do not come out
of compression.
Express your answer in units of kilonewtons.
Chapter 8 Solutions
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Ch. 8 - A power screw is 25 mm in diameter and has a...Ch. 8 - Using the information in the footnote of Table...Ch. 8 - Show that for zero collar friction the efficiency...Ch. 8 - A single-threaded power screw is 25 mm in diameter...Ch. 8 - The machine shown in the figure can be used for a...Ch. 8 - The press shown for Prob. 8-5 has a rated load of...Ch. 8 - For the screw clamp shown, a force is applied at...Ch. 8 - The C clamp shown in the figure for Prob. 8-7 uses...Ch. 8 - Find the power required to drive a 1.5-in power...Ch. 8 - A single square-thread power screw has an input...
Ch. 8 - Prob. 11PCh. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - Prob. 13PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Repeat Prob. 8-14 with the addition of one 12 N...Ch. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Two identical aluminum plates are each 2 in thick,...Ch. 8 - Prob. 18PCh. 8 - A 30-mm thick AISI 1020 steel plate is sandwiched...Ch. 8 - Prob. 20PCh. 8 - Prob. 21PCh. 8 - Prob. 22PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - An aluminum bracket with a 12-in thick flange is...Ch. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - A 34 in-16 UNF series SAE grade 5 bolt has a 34-in...Ch. 8 - From your experience with Prob. 8-26, generalize...Ch. 8 - Prob. 28PCh. 8 - Prob. 29PCh. 8 - Prob. 30PCh. 8 - For a bolted assembly with eight bolts, the...Ch. 8 - Prob. 32PCh. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - Prob. 37PCh. 8 - Prob. 38PCh. 8 - 837 to 840 Repeat the requirements for the problem...Ch. 8 - Prob. 40PCh. 8 - 841 to 844 For the pressure vessel defined in the...Ch. 8 - Prob. 42PCh. 8 - Prob. 43PCh. 8 - Prob. 44PCh. 8 - Bolts distributed about a bolt circle are often...Ch. 8 - The figure shows a cast-iron bearing block that is...Ch. 8 - Prob. 47PCh. 8 - Prob. 48PCh. 8 - Prob. 49PCh. 8 - Prob. 50PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - Prob. 52PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - For the pressure cylinder defined in the problem...Ch. 8 - A 1-in-diameter hot-rolled AISI 1144 steel rod is...Ch. 8 - The section of the sealed joint shown in the...Ch. 8 - Prob. 61PCh. 8 - Prob. 62PCh. 8 - Prob. 63PCh. 8 - Prob. 64PCh. 8 - Using the Goodman fatigue criterion, repeat Prob....Ch. 8 - The figure shows a bolted lap joint that uses SAE...Ch. 8 - Prob. 67PCh. 8 - A bolted lap joint using ISO class 5.8 bolts and...Ch. 8 - Prob. 69PCh. 8 - The figure shows a connection that employs three...Ch. 8 - A beam is made up by bolting together two cold...Ch. 8 - Prob. 72PCh. 8 - Prob. 73PCh. 8 - Prob. 74PCh. 8 - A vertical channel 152 76 (see Table A7) has a...Ch. 8 - The cantilever bracket is bolted to a column with...Ch. 8 - Prob. 77PCh. 8 - The figure shows a welded fitting which has been...Ch. 8 - Prob. 79PCh. 8 - Prob. 80PCh. 8 - Prob. 81P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- ! Required information For a bolted assembly with N = 6 bolts, the stiffness of each bolt is kb=1 Mlbf/in and the stiffness of the members is km = 20 Mlbf/in per bolt. A repeated external load of W= 72 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. Assume the bolts are preloaded to 75 percent of the proof load and the external load is a repeated load. Number of Bolts, N Bolt Grade, G Bolt Diameter, d 6 SAE 8 1/2 in Determine the fatigue factor of safety for the bolts using the Goodman failure criterion. The fatigue factor of safety for the bolts using the Goodman failure criterion isarrow_forwardGive me correct answers pleasearrow_forwardTwo 1/4 in × 8 in A36 steel plates are joined with a lap joint using 3/4 in A325-N bolts. If a concentric unfactored live load of 50 kips (dead load = 0) is required to be resisted by the connection and the bolt shear strength controls the design, the minimum required number of bolts is?arrow_forward
- Problem 3: A Hexagonal bolt connects two members. The joint has a gap 1 = 2 in and the applied load is 2000 lb. Both of the clamped parts are steel. A preload of 90% the bolt's proof strength will be applied first. For this design, an SAE grade 1, 5/16"-18 UNC-2A bolt is chosen made from A307 with rolled threads. Washers are included between the head and the joint, and between the nut and the joint. Determine a suitable length for the bolt? Find its safety factor against yielding and against joint separation. Are these values acceptable?arrow_forwardRequired information For a bolted assembly with eight bolts, the stiffness of each bolt is kb = 0.8 MN/mm and the stiffness of the members is km = 2.6 MN/mm per bolt. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly. Assume the external load is equally distributed to all the bolts. It has been determined to use M6 x 1 class 5.8 bolts with rolled threads. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum external load Pmax that can be applied to the entire joint without causing the members to come out of compression. The maximum external load for this case is 0.15625 N.arrow_forward3. An M16 x 2 bolt with a slotted hex nut is used to clamp together two 25 mm steel plates. The joint is assembled with a size 16 N washer underneath the bolt head. The bolt is a 5.8 class metric grade, with a proof strength of 380 MPa. The joint is intended to be permanent. Determine a suitable length for the bolt, rounded up to the nearest standard size in millimeters. Calculate the bolt stiffness, the elongation of the bolt after the necessary preload is developed, and the bolt torque required to apply the preload. Assume that coefficients of friction between the bolt, nut, and collar are all ~0.15. For steel, use E = 207 GPa. Standard threaded fastener lengths, dimensions of hexagonal nuts, and dimensions of metric plain washers are provided in the textbook appendices.arrow_forward
- For a bolted assembly, the stiffness of each bolt is ka = 700 MN/m and the stiffness of the members is km = 2100 MN/m per bolt. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly. An external load is applied to the entire joint with P = 360 kN. Assume the load is equally distributed to all the bolts. It has been determined to use M12x1.75 grade 8.8 bolts with rolled threads. (a) Determine the minimum number of bolts necessary to avoid yielding of the bolts. (b) Determine the minimum number of bolts necessary to avoid joint separation.arrow_forwardNo cursivearrow_forwardDesign of a bolted assembly using a single M16x2 class 8.8 coarse-thread bolt has resulted in a joint where bolt stiffness is k, = 6 N/mm and the overall member stiffness - 18 N/mm. The fastener is to be reused (nonpermanent). Question 1 Value of joint stiffness constant: 0.25 4.0 0.5 0.1 Question 2 Magnitude of bolt tightening load (preload) Fi [kv]: 85 71 94 63arrow_forward
- A factor of safety of 2.5 is used for the bolts in the assembly below. The ultimate shear stress of the magnesium alloy bolts is 20.0ksi. What should be the diameter of the bolts? 10 kip 5 kip 5 kip Diameter = inarrow_forward4. Determine the design stress for bolts in a cylinder cover where the load is fluctuating due to gas pressure. The maximum load on the bolt is 50 kN and the minimum is 30 kN. The load is unpredict- able and factor of safety is 3. The surface of the bolt is hot rolled and the suface finish factor is 0.9. During a simple tension test and rotating beam test on ductile materials (40 C 8 steel annealed), the following results were obtained : Diameter of specimen =12.5 mm; Yield strength= 240 MPa; Ultimate strength= 450 MPa; Endurance limit = 180 MPa. [Ans. 65.4 MPa]arrow_forwardzLm An M8x1 bolt joins to members of 40 mm total thickness. The bolt and members are made of the same material (₂ = 300 MPa, E = 120 GPa), Fi=3KN, Pw=4KN. Check join failure.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning