Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 42, Problem 2MC
A glitch appears in the waveform of a vehicle speed sensor. Which of the following is not a probable cause of the problem?
a. A loose connector
b. A damaged wire
c. A poorly mounted sensor
d. A damaged magnet in the sensor
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
d)
Figure 1 below shows a vehicle which has taken a curve at very high speed, but
since the road was slippery, the rear of the car swings to one side. With an aid of
sketch, explain what condition it is and how Electronic Stability Programme will act on
the vehicle without braking applied condition.
Figure 1
Describe at least two methods of checking
the operation of Hall-effect sensors used in
engine management systems. (40 - 60
words)
5-a)What are the two types of Fluid Pressure Sensor? Explain diaphragm sensors with a neat schematic sketch.
Chapter 42 Solutions
Automotive Technology
Ch. 42 - While discussing the CVT transaxie used in Toyota...Ch. 42 - Although computers receive different information...Ch. 42 - What happens if the TCM determines that the...Ch. 42 - Prob. 4SACh. 42 - List five things that could cause incorrect shift...Ch. 42 - Most late-model transmission control systems have...Ch. 42 - What inputs are of prime importance to a computer...Ch. 42 - What are the advantages of using electronic...Ch. 42 - Voltage generation devices are typically used to...Ch. 42 - True or False? On most late-model EAT systems,...
Ch. 42 - True or False? The neutral safety switch and...Ch. 42 - Which of the following is not a voltage-generating...Ch. 42 - A glitch appears in the waveform of a vehicle...Ch. 42 - Prob. 3MCCh. 42 - Which of the following would probably not be...Ch. 42 - Technician A says that some systems use a special...Ch. 42 - Technician A says that shift solenoids direct...Ch. 42 - Technician A says that throttle position is an...Ch. 42 - Technician A says that a faulty TP sensor can...Ch. 42 - Technician A says that some shift solenoids can be...Ch. 42 - An electronically controlled transmission has...Ch. 42 - While discussing transmission adaptive learning:...Ch. 42 - While discussing valve body assemblies in...Ch. 42 - A transmission has delayed upshifts under all...Ch. 42 - While diagnosing the cause of TCC shudder:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When testing a frequency varying MAF: Technician A says that the frequency should increase with an increase in engine speed. Technician B says that when observed on a lab scope, the signal from the sensor should be a square wave. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following is the most likely cause of a lean condition during acceleration and cruising speeds? a. A defective oxygen sensor b. A defective PCM c. A defective ECT sensor d. A defective MAF sensorarrow_forwardwhat is meant by sensor bias voltage in automotivearrow_forward
- 3- Contact Type displacement sensors makes direct contact with the object being monitored. Select one: True Falsearrow_forwardThe input and output of a sensor has nonlinear relation. True/ Falsearrow_forwardDescribe the two basic types of passenger weightdetection sensors used in most vehiclesarrow_forward
- When inspecting wheel-speed sensors, check for all of the following except buildup of metal or rust on the sensor. proper contact between the pole piece and tone ring. secure sensor mounting. condition of the tone ring teeth.arrow_forwardTrue or False? On some engines, if the gap between the crankshaft sensor and its trigger wheel is outside specifications, the sensor should be replaced.arrow_forwardA vehicle with a direct TPMS is brought into a shop with all sensors failing to read any pressure at all. Technician A says it’s likely that all 4 sensors died at once. Technician B says it may be due to a damaged or faulty TPMS antenna. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forward
- When using a Vernier motion sensor to record the position of a cart on a track, the sensor itself: Select one: a. may not be properly aligned, in which case you should call the TA b. is always perfectly aligned and not adjustable c. requires you to test it's alignment before attempting to take dataarrow_forwardExplain the Working of Ultrasonic Doppler flow sensor with Diagramarrow_forwardWhich of the following statements about zirconium oxygen sensors is not true? The normal operating range for an O2S is between 0 and 1 volt. If the sensors voltage toggles between 0 volts and 500 millivolts, it is operating normally. The voltage signal from an upstream O2S should have seven cross counts within 5 seconds with the engine running without a load at 2,500 rpm. Engine control systems monitor the activity of the O2S and store a code when the sensors output is not within the desired range.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY