Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 42, Problem 6SA
Most late-model transmission control systems have adaptive learning. What does this mean?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
i need the answer quickly
b) Base on your analysis, why the value of Belt Drive with V-Belt is having a lower coefficientcompared to flat belt?
what factors determine the design of the power transmission mechanisms in a rear wheel drive van (Diesel) and how do you calculate power and torque at the driveshaft, assuming the following: its 5 speed transmission, Gear system efficiency is 88% Gear ratios: 1 st: 4.17:1
2 nd 2.34:1
3 rd 1.52:1
4 th 1.14:1
and power and torque to be calculated at the point where engine is generating its maximum power
Chapter 42 Solutions
Automotive Technology
Ch. 42 - While discussing the CVT transaxie used in Toyota...Ch. 42 - Although computers receive different information...Ch. 42 - What happens if the TCM determines that the...Ch. 42 - Prob. 4SACh. 42 - List five things that could cause incorrect shift...Ch. 42 - Most late-model transmission control systems have...Ch. 42 - What inputs are of prime importance to a computer...Ch. 42 - What are the advantages of using electronic...Ch. 42 - Voltage generation devices are typically used to...Ch. 42 - True or False? On most late-model EAT systems,...
Ch. 42 - True or False? The neutral safety switch and...Ch. 42 - Which of the following is not a voltage-generating...Ch. 42 - A glitch appears in the waveform of a vehicle...Ch. 42 - Prob. 3MCCh. 42 - Which of the following would probably not be...Ch. 42 - Technician A says that some systems use a special...Ch. 42 - Technician A says that shift solenoids direct...Ch. 42 - Technician A says that throttle position is an...Ch. 42 - Technician A says that a faulty TP sensor can...Ch. 42 - Technician A says that some shift solenoids can be...Ch. 42 - An electronically controlled transmission has...Ch. 42 - While discussing transmission adaptive learning:...Ch. 42 - While discussing valve body assemblies in...Ch. 42 - A transmission has delayed upshifts under all...Ch. 42 - While diagnosing the cause of TCC shudder:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe at least two methods of checking the operation of Hall-effect sensors used in engine management systems. (40 - 60 words)arrow_forwardWhat is Qts number in a driver? Also what are T/S parameters?arrow_forwardWhat is the difference between static lateral stability and lateral stability? I see textbooks differentiate between the two but I don’t understand the differencearrow_forward
- What is meant by 'sensor bias voltage' and how is it used in an engine management system? (70 - 100 words)arrow_forward۸:۲۹ م KOREK TELECOMIKOREK Asiacell I%A. Choose the most correct answer .for each of the following The picture shows DD single disk clutch. O chain drive. drum brake. disk brake. O cone clutch. multi-disk clutch. !arrow_forwardSEÇT A qud FClutquessv veion) (Matitesum pthedblum prt gen (Answe Question 1 A car manufacturing company is in the process of testing a new vehicular transmission system. Figure 1 shows an outline of the system arrangement. As usual, the power generated by the engine is smoothed out by a flywheel at the end of the camshaft. A multi-plate clutch is affixed to the flywheel and transfers power to the main shaft via the layshaft. Engine 23 4 5 R Main Shaft Clutch & flywheel Layshaft Figure 1: Schematic of transmission arrangement The output torque from the engine is given by the expression: 510 + 46 sin 20 Nm, per rotational cycle and spins at an average of 4000 rpm. The attached flywheel has a coefficient of speed fluctuation of 0.15. Assuming a constant load torque requirement, determine: a) The maximum fluctuation of energy and the average power output at the flywheel face. b) The mass moment of inertia of the flywheel. c) The maximum and minimum speeds of the flywheel.arrow_forward
- Analyze the diagram above. Some of the drives system of the figure above has its own depreciation on its efficiencies as the lifecycle progress. State one of the reasons of why the efficiency drop on and explain any method that can increase this efficiency especially on the directional control valvearrow_forwardNeed valid explaination (neat and clean handwritten solution).. I will upvote if you fulfilled all criterion stated above. THANKS. Don't give copied answer.arrow_forwardExplain the key functional and operational differences between a conventional continuously variable transmissions (CVT) and torque converter and the units fitted to hybrid electric vehicles. In your answer, briefly describe how a CVT transmission operates in the hybrid vehicle. (100 - 150 words)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License