
Concept explainers
Find the maximum power transferred to resistor R in the circuit of Fig. 4.135.
Figure 4.135

Calculate the maximum power delivered to the resistor R of the circuit shown in Figure 4.135.
Answer to Problem 69P
The maximum power delivered to the variable resistor R is infinity.
Explanation of Solution
Given data:
Refer to Figure 4.135 in the textbook.
The voltage source is 100 V.
Formula used:
Write the expression to find the power delivered to the resistor.
Here,
Calculation:
The given circuit is modified as shown in Figure 1.
In Figure 1, the voltage source with series resistance is converted into current source with parallel resistance using source transformation. The current (I) is calculated by using Ohm’s law.
The source transformation is shown in Figure 2.
In Figure 2, apply Kirchhoff’s current law at node voltage
Simplify the equation as follows,
In Figure 2, apply Kirchhoff’s current law at node voltage
Substitute
Simplify the equation as follows,
Substitute
Since, the voltage at node
Refer to Figure 4.135 in the textbook.
In the given circuit, find the short circuit current by shorting the resistor R.
The modified circuit is shown in Figure 3.
To find the short circuit current
Substitute 0 for
In Figure 3, apply Kirchhoff’s current law at node voltage
Substitute 0 for
The Thevenin resistance is,
Substitute
The negative equivalent resistance indicates that an active device (dependent source) presents in the circuit, since the circuit cannot have a negative resistance in a purely passive circuit. The negative resistance for the equivalent circuit means that both the resistance and the source will effectively delivers the power to load.
Since the resistance cannot be the negative, the correct answer will be
Conclusion:
Thus, the maximum power delivered to the variable resistor R is infinity.
Want to see more full solutions like this?
Chapter 4 Solutions
EBK FUNDAMENTALS OF ELECTRIC CIRCUITS
- Can you help me find the result of an integral 0/2 a² X + a dxarrow_forwardQ1/Sketch the root locus for the system shown in Figure 1 and find the following: a. The exact point and gain where the locus crosses the jo-axis b. The breakaway point on the real axis c. The range of K within which the system is stable d. Angles of departure and arrival R(s) + K(s²-4s +20) C(s) (s+2)(s + 4)arrow_forwardExam2 Subject: (Numerical Analysis) Class: Third Date: 27/4/2025 Time: 60 minutes Q1. For what values of k does this system of equations has no solution? (use Gauss-Jordan eliminations) kx + y + z = 1 x+ky + z = 1 x+y+kz=1arrow_forward
- Consider the Difference equation of a causal Linear time-invariant (LTI) system given by: (y(n) - 1.5y(n - 1) + 0.5y(n = 2) = x(n) a) Implement the difference equation model of this system. b) Find the system transfer function H(z). c) For an input x(n) = 8(n), determine the output response y(n). d) Verify the initial value theorem y(0) with part (c).arrow_forwardQ5B. Find the type of the controller in the following figures and use real values to find the transfer function of three of them[ Hint Pi,Pd and Lead,lag are found so put the controller with its corresponding compensator]. R₁ R₂ Rz HE C2 RA HE R₁ R2 RA とarrow_forwardQ1// Sketch the root locus for the unity feedback system. Where G(s)=)= K S3+252 +25 and find the following a. Sketch the asymptotes b. The exact point and gain where the locus crosses the jo-axis c. The breakaway point on the real axis d. The range of K within which the system is stable e. Angles of departure and arrival.arrow_forward
- Determine X(w) for the given function shown in Figure (1) by applying the differentiation property of the Fourier Transform. Figure (1) -1 x(t)arrow_forwardCan you solve a question with a drawing Determine X(w) for the given function shown in Figure (1) by applying the differentiation property of the Fourier Transform. Figure (1) -1 x(t)arrow_forwardAn inductor has a current flow of 3 A when connected to a 240 V, 60 Hz power line. The inductor has a wire resistance of 15 Find the Q of the inductorarrow_forward
- صورة من s94850121arrow_forwardThe joint density function of two continuous random variables X and Yis: p(x, y) = {Keós (x + y) Find (i) the constant K 0 2 0arrow_forwardShow all the steps please, Solve for the current through R2 if E2 is replaced by a current source of 10mA using superposition theorem. R5=470Ω R2=1000Ω R6=820Ωarrow_forwardarrow_back_iosSEE MORE QUESTIONSarrow_forward_ios
- Introductory Circuit Analysis (13th Edition)Electrical EngineeringISBN:9780133923605Author:Robert L. BoylestadPublisher:PEARSONDelmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage LearningProgrammable Logic ControllersElectrical EngineeringISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
- Fundamentals of Electric CircuitsElectrical EngineeringISBN:9780078028229Author:Charles K Alexander, Matthew SadikuPublisher:McGraw-Hill EducationElectric Circuits. (11th Edition)Electrical EngineeringISBN:9780134746968Author:James W. Nilsson, Susan RiedelPublisher:PEARSONEngineering ElectromagneticsElectrical EngineeringISBN:9780078028151Author:Hayt, William H. (william Hart), Jr, BUCK, John A.Publisher:Mcgraw-hill Education,





