An FM signal with 75 kHz deviation, has an input signal-to-noise ratio of 18 dB, with a modulating frequency of 15 kHz. 1) Find SNRO at demodulator o/p. 2) Find SNRO at demodulator o/p if AM is used with m=0.3. 3) Compare the performance in case 1) and 2).. Hint: for single tone AM-DSB-LC, SNR₁ = (2m²) (4)

An FM signal with 75 kHz deviation, has an input signal-to-noise ratio of 18 dB, with a modulating frequency of 15 kHz. 1) Find SNRO at demodulator o/p. 2) Find SNRO at demodulator o/p if AM is used with m=0.3. 3) Compare the performance in case 1) and 2).. Hint: for single tone AM-DSB-LC, SNR₁ = (2m²) (4)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need proper solution for the following( underdstandable writing and well explained) thank you What is resonance in LCR circuit? and tell the difference between impedance and resistance?
hand written answer,please
Electrical Engineering PROBLEM SET QI. For the MOSFET circuit below, input is sinusoidal signal of amplitude 1V and frequency 50HZ. Find, the DC operating point, Plot the frequency response and Plot the input, output and transfer characteristics and find out the small signal equivalent. Assume an overdrive voltage of 0.2V Use MOSFET 500nm Library file provided. AG-PPA <80 K 1-2nF Q1 Vin
Q. No 1. For the given analog signal, follow the proper steps to convert this signal to digital signal. (Take voltage levels L = 8, n= 3). Also assign proper coding to each voltage level and draw the resultant digital waveform for the given analog signal. Sample times Arnalog imput Time
For the filter: a) Determine type of filter and the cut-off frequency (Fc). Determine the peak voltage at the cut-off frequency (Fc). b) Find GAIN (Vo/Vi) at f = .1*Fc . Find GAIN (Vo/Vi) at f = 10*Fc . c) Determine the frequency at which GAIN = .4 (i.e., Vo = .4*Vi) . Draw the “Frequency Response Plot” in “Log-Log” format .
1.3 We have a band pass signal in the frequency band, 450 Hz to 460 Hz. The carrier frequency is 455 Hz. We want to sample the signal. We have two choices: 1) Sample at more than twice the maximum frequency and 2) Sample at more than twice the bandwidth. Compare the two options of sampling the signal in terms of sampling frequency.
According to the maximum power transfer rule, it must be in order to draw maximum energy.............. from the circuit.What should come in yhe blank? Please choose one: a. is equal to the output resistance of the circuit and the input resistance of the receiver circuit. B. The input resistance of the ob circuit is small c. The output resistance of the circuit is greater than the input resistance of the receiver circuit D. The output resistance of the Od circuit is less than the inputE. e is the largest starting resistance of the circuit
Q1. For the MOSFET circuit below, input is sinusoidal signal of amplitude IV and frequency 50Hz. Find, the DC operating point, Plot the frequency response and Plot the input, output and transfer characteristics and find out the small signal equivalent. Assume an overdrive voltage of 0.2V Use MOSFET 500nm Library file provided. F Vdd=5V -=80 K R1 (1 1.20F
7-22 Abasehand signal with frequency components from near de to 15 kHz frequency modulates a 200-kHz carrier, and the frequency deviation is +3 kHz. The signal is applied as the input to a cascade of two frequency triplers and one frequency doubler. Determine the output (a) center fre- quency, (b) frequency deviation, and (c) deviation ratio.
What is the function of a filter? What is a typical application? What is an active filter?
One way to control power, in an electronic system is to using the PWM (pulse width modulation) method. To create an adjustable signal pulse width, one of which is used a window comparator as shown in the figure (VCC = +12 V, VEE = -12 V). If a 10 Vpp 10 kHz signal is given as an input, determine the complete output waveform by displaying the reference voltage. (compare with the input)
A step-up chopper has input voltage of 220v and o/pvoltage of 660v. If the non-conducting time of the thyristorchopper is 100μs compute the pulse width of the outputvoltage . If the pulse width is halved for constant frequencyoperation Find the new output voltage and chopper frequency